S-1131B25UA-N4KTFG Seiko Instruments, S-1131B25UA-N4KTFG Datasheet - Page 14
![IC REG LDO 300MA 2.5V SOT89-3](/photos/12/63/126323/s-812c50aua-c3et2g_sml.jpg)
S-1131B25UA-N4KTFG
Manufacturer Part Number
S-1131B25UA-N4KTFG
Description
IC REG LDO 300MA 2.5V SOT89-3
Manufacturer
Seiko Instruments
Datasheet
1.S-1131B15UA-N4ATFG.pdf
(30 pages)
Specifications of S-1131B25UA-N4KTFG
Regulator Topology
Positive Fixed
Voltage - Output
2.5V
Voltage - Input
Up to 6.5V
Voltage - Dropout (typical)
0.3V @ 100mA
Number Of Regulators
1
Current - Output
300mA (Min)
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
SC-62, SOT-89, TO-243 (3 Leads + Tab)
Number Of Outputs
1
Polarity
Positive
Input Voltage Max
6.5 V
Output Voltage
2.5 V
Output Type
Fixed
Dropout Voltage (max)
0.49 V at 100 mA
Output Current
300 mA
Line Regulation
0.2 % / V
Load Regulation
40 mV
Voltage Regulation Accuracy
1 %
Maximum Power Dissipation
0.5 W
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
The S-1131 Series performs phase compensation using the internal phase compensator in the IC and the ESR
(Equivalent Series Resistance) of the output capacitor to enable stable operation independent of changes in the
output load. Therefore, always place a capacitor (C
For stable operation of the S-1131 Series, it is essential to employ a capacitor whose ESR is within an optimum
range. Using a capacitor whose ESR is outside the optimum range (approximately 0.5 to 5 Ω), whether larger
or smaller, may cause an unstable output, resulting in oscillation. For this reason, a tantalum electrolytic
capacitor is recommended.
When a ceramic capacitor or an OS capacitor with a low ESR is used, it is necessary to connect an additional
resistor that serves as the ESR in series with the output capacitor.
approximately 0.5 to 5 Ω, which varies depending on the usage conditions, so perform sufficient evaluation for
selection. Ordinarily, around 1.0 Ω is recommended.
Note that an aluminum electrolytic capacitor may increase the ESR at a low temperature, causing oscillation.
When using this kind of capacitor, perform thorough evaluation, including evaluation of temperature
characteristics.
14
HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1131 Series
Selection of Output Capacitor (C
3. Shutdown pin (ON/OFF pin)
The products with shutdown function performs starting and a stop the regulator.
When the ON/OFF pin is set to the shutdown level, the operation of all internal circuits stops, and the built-
in P-channel MOS FET output transistor between the VIN pin and VOUT pin is turned off to substantially
reduce the current consumption. The VOUT pin becomes the Vss level due to the internally divided
resistance of several hundreds kΩ between the VOUT pin and VSS pin.
The structure of the ON/OFF pin is as shown in Figure 14. Since the ON/OFF pin is neither pulled down
nor pulled up internally, do not use it in the floating state. In addition, note that the current consumption
increases if a voltage of 0.3 V to V
used, connect it to the VSS pin if the logic type is “A” and to the VIN pin if it is “B”.
Logic Type
ON/OFF
A
A
B
B
Figure 14
“H”: Power off
“H”: Power on
“L”: Power on
“L”: Power off
ON/OFF Pin
VSS
VIN
Internal Circuits
IN
– 0.3 V is applied to the ON/OFF pin. When the ON/OFF pin is not
Operating
Operating
Stopped
Stopped
Seiko Instruments Inc.
L
)
Table 7
L
) of 2.2 μF or more between VOUT and VSS pins.
VOUT Pin Voltage
Set value
Set value
V
V
SS
SS
level
level
The required resistance value is
Current Consumption
I
I
I
I
SS1
SS2
SS2
SS1
Rev.4.0
_00