S-818A29AMC-BGJT2G Seiko Instruments, S-818A29AMC-BGJT2G Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/5/590/seiko_instruments_sml.jpg)
S-818A29AMC-BGJT2G
Manufacturer Part Number
S-818A29AMC-BGJT2G
Description
IC REG LDO 150MA 2.9V SOT23-5
Manufacturer
Seiko Instruments
Datasheet
1.S-818A20AMC-BGAT2G.pdf
(32 pages)
Specifications of S-818A29AMC-BGJT2G
Regulator Topology
Positive Fixed
Voltage - Output
2.9V
Voltage - Input
Up to 10V
Voltage - Dropout (typical)
0.38V @ 60mA
Number Of Regulators
1
Current - Output
150mA (Min)
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
SOT-23-5, SC-74A, SOT-25
Number Of Outputs
1
Polarity
Positive
Input Voltage Max
10 V
Output Voltage
2.9 V
Output Type
Fixed
Dropout Voltage (max)
0.61 V at 60 mA
Output Current
150 mA
Line Regulation
0.2 % / V
Load Regulation
50 mV
Voltage Regulation Accuracy
2 %
Maximum Power Dissipation
0.6 W
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Rev.3.0
3. ON/OFF pin (Shutdown pin)
Selection of Output Capacitor (C
This pin activates and inactivates the regulator.
When the ON/OFF pin is switched to the shutdown level, the operation of all internal circuit stops, the
built-in Pch MOS FET output transistor between VIN and VOUT pin is switched off, suppressing current
consumption. The VOUT pin goes to the Vss level due to internal divided resistance of several MΩ
between VOUT pin and VSS pin.
The structure of the ON/OFF pin is shown in Figure 13. Since the ON/OFF pin is neither pulled down nor
pulled up internally, do not keep it in the floating state. Current consumption increases if a voltage of
0.3 V to V
pin for product type "A" and to the VSS pin for product type "B".
The S-818 Series needs an output capacitor between VOUT pin and VSS pin for phase compensation. A
small ceramic or an OS electrolyte capacitor of 2 μF or more can be used. When a tantalum or an
aluminum electrolyte capacitor is used, the capacitance must be 2 μF or more and the ESR must be 10 Ω
or less.
Attention should be paid not to cause an oscillation due to increase of ESR at low temperatures when an
aluminum electrolyte capacitor is used.
Evaluate the performance including temperature characteristics before prototyping the circuit.
Overshoot and undershoot characteristics differ depending upon the type of the output capacitor. Refer
to the “C
Product type
Figure 13 The structure of the ON/OFF Pin
_00
A
A
B
B
L
IN
dependence” data in “ Transient Response Characteristics”.
−0.3 V is applied to the ON/OFF pin. When the shutdown pin is not used, connect it to the VIN
ON/OFF
“H”: Shutdown
“L”: Shutdown
“H”: Power on
“L”: Power on
ON/OFF pin
VSS
Table 6 ON/OFF pin function by product type
VIN
Internal circuit
Operating
Operating
Seiko Instruments Inc.
L
Stop
Stop
)
LOW DROPOUT CMOS VOLTAGE REGULATOR
VOUT pin voltage
Set value
Set value
V
V
SS
SS
level
level
Current consumption
I
I
I
I
ss1
ss2
ss2
ss1
S-818 Series
13