AS1353-30-T austriamicrosystems, AS1353-30-T Datasheet - Page 8

• Manufacturer Part Number: AS1353-30-T
• Description: IC REG LDO 150MA 3.0V TSOT23-5
• Manufacturer: austriamicrosystems

Specifications of AS1353-30-T

• Package / Case: SOT-23-5, SC-74A, SOT-25
• Mounting Type: Surface Mount
• Current - Output: 150mA (Min)
• Voltage - Output: 3V
• Voltage - Input: Up to 5.5V
• Operating Temperature: -40°C ~ 85°C
• Regulator Topology: Positive Fixed
• Voltage - Dropout (typical): 0.06V @ 150mA
• Number Of Regulators: 1
• Current - Limit (min): 160mA
• Primary Input Voltage: 4V
• Output Voltage Fixed: 3V
• Dropout Voltage Vdo: 60mV
• No. Of Pins: 5
• Output Current: 150mA
• Operating Temperature Range: -40°C To +85°C
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AS1353/AS1356
Data Sheet
8 Detailed Description
The AS1353/AS1356 are low-dropout, low-quiescent-current linear regulators intended for LDO regulator applications
where output current load requirements range from no load to 150mA. All devices come standard with fixed output volt-
ages of 1.5 to 3.6V (see Ordering Information on page
Figure 12. Block Diagram
As illustrated in Figure 12, the devices comprise a 1.25V reference, error amplifier, P-channel MOSFET pass transis-
tor, power-OK comparator, internal feedback voltage divider, current limiter, reverse-battery protection, thermal sensor
and shutdown logic.
The 1.25V bandgap reference is connected to the inverting input of the error amplifier. The error amplifier compares
this reference with the feedback voltage and amplifies the difference. If the feedback voltage is lower than the refer-
ence voltage, the P-channel MOSFET gate is pulled lower, allowing more current to pass to the output, and increases
the output voltage. If the feedback voltage is too high, the pass-transistor gate is pulled up, allowing less current to
pass to the output. The output voltage feeds back through an internal resistor voltage divider connected to pin OUT.
Output Voltages
Standard products are factory-set with output voltages of from 1.5 to 3.6V. A two-digit suffix of the part number identi-
fies the nominal output voltage (see Ordering Information on page 12).
Non-standard devices are available. Contact austriamicrosystems AG for more information.
Internal P-Channel MOSFET Pass Transistor
The integrated 0.5Ω (typ) P-channel MOSFET pass transistor requires no base drive, which reduces quiescent current
significantly, and does not exhibit the problems associated with PNP-based regulators, such as dropout when the pass
transistor saturates or high base-drive currents under large load conditions.
The devices consume only 115µA quiescent current in dropout, light-load, or heavy-load applications (see Typical
Operating Characteristics on page 6).
Power-OK
The AS1356’s power-ok circuitry is built around an N-channel MOSFET. The circuitry monitors the voltage on pin 5
(OUT) and if the voltage goes out of regulation (e.g. during dropout, current limit, or thermal shutdown) pin POK goes
low.
www.austriamicrosystems.com
SHDNM
BP
GND
IN
1
- D e t a i l e d D e s c r i p t i o n
Current Reference
Bandgap Voltage
Protection
Protection
Reverse-
Overload
Thermal
Battery
&
Control Logic
Trimmable
Reference
Shutdown/
Power-On
Voltage
95%
Revision 1.03
12).
+
-
Amplifier
Error
AS1353/AS1356
–
+
R
R
2
1
OUT
POK
1
2
AS1353 only
AS1356 only
2
AS1356 only
8 - 13