MAX8516EUB+T Maxim Integrated Products, MAX8516EUB+T Datasheet - Page 8

• Manufacturer Part Number: MAX8516EUB+T
• Description: IC REG LDO 1A 10-UMAX
• Manufacturer: Maxim Integrated Products
• Type: Linearr

Specifications of MAX8516EUB+T

• Regulator Topology: Positive Adjustable
• Voltage - Output: 0.5 ~ 3.4 V
• Voltage - Input: 1.43 ~ 3.6 V
• Voltage - Dropout (typical): 0.1V @ 1A
• Number Of Regulators: 1
• Current - Output: 1A
• Current - Limit (min): 1.6A
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Package: 10uMAX EP
• Function: LDO
• Number Of Outputs: 1
• Input Voltage Range: 3.6 to 1.425 V
• Output Voltage: 0.5 to 3.4 V
• Maximum Output Current: 1 A
• Output Type: Adjustable
• Accuracy: ±0.6 %
• Typical Dropout Voltage @ Current: 0.1@1A V
• Polarity: Positive
• Input Voltage Max: 3.6 V
• Dropout Voltage (max): 0.2 V at 1 A
• Output Current: 1 A
• Line Regulation: 0.15 % / V
• Load Regulation: 0.1 % / A
• Voltage Regulation Accuracy: 0.6 %
• Maximum Power Dissipation: 0.824 W
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The maximum power dissipation depends on the ther-
mal resistance of the IC package and circuit board, the
temperature difference between the die junction and
ambient air, and the rate of airflow. The power dissipat-
ed in the device is P = I
The package features an exposed thermal pad on its
underside. This pad lowers the thermal resistance of
the package by providing a direct heat conduction
path from the die to the PCB.
Additionally, the ground pins (GND) perform the dual
function of providing an electrical connection to system
ground and channeling heat away. Connect the
exposed backside pad and GND to the system ground
using a large pad or ground plane, or multiple vias to
the ground plane layer.
Capacitors are required at the MAX8516/MAX8517/
MAX8518 inputs and outputs for stable operation over the
full temperature range and with load currents up to 1A.
Connect a 1µF capacitor between IN and ground and a
4.7µF capacitor with low equivalent series resistance
(ESR) between OUT and ground for 1A output current.
The input capacitor (C
the input supply. If input-supply source impedance is
high, place a larger input capacitor close to IN to prevent
V
itors can be used for output currents less than 1A.
Calculate C
1.425V to 3.6V Input, 1A,
0.2V Dropout LDO Regulators
8
IN
Operating Region and Power Dissipation
_______________________________________________________________________________________
sagging due to load transients. Smaller output capac-
C
OUT
OUT
as follows:
Applications Information
=
I
OUT MAX
IN
) lowers the source impedance of
OUT
(
Capacitor Selection and
✕
)
(V
×
Regulator Stability
IN
(
µ 1 200
- V
F
OUT
).
mA
)
The MAX8516/MAX8517/MAX8518 are designed to
operate with low dropout voltages and low quiescent
currents while still maintaining good noise, transient
response, and AC rejection (see the Typical Operating
Characteristics for a plot of Power-Supply Rejection
Ratio (PSRR) vs. Frequency). When operating from
noisy sources, improved supply-noise rejection and
transient response can be achieved by increasing the
values of the input and output bypass capacitors and
through passive filtering techniques. The MAX8516/
MAX8517/MAX8518 load-transient response graphs
(see the Typical Operating Characteristics ) show two
components of the output response: a DC shift from the
output impedance due to the load current change, and
the transient response. A typical transient overshoot for
a step change in the load current from 20mA to 1A is
45mV. Use larger output ceramic capacitors greater
than 4.7µF up to 50µF to attenuate the overshoot.
Noise, PSRR, and Transient Response