MIC5216-3.3BMM TR Micrel Inc, MIC5216-3.3BMM TR Datasheet
![IC REG LDO 500MA 1% 3.3V 8-MSOP](/photos/18/29/182940/8-msop_sml.jpg)
MIC5216-3.3BMM TR
Specifications of MIC5216-3.3BMM TR
MIC5216-3.3BMMTR
Related parts for MIC5216-3.3BMM TR
MIC5216-3.3BMM TR Summary of contents
Page 1
... Dropout is typically 10mV at light loads and less than 500mV at full load. The MIC5216 is designed to provide a peak output current for startup conditions where higher inrush current is demanded. It features a 500mA peak output rating. Continuous output current is limited only by package and layout ...
Page 2
... MIC5216-3.3BMM MIC5216-5.0BMM MIC5216-2.5BM5 LH25 MIC5216-3.3BM5 LH33 MIC5216-3.6BM5 LH36 MIC5216-5.0BM5 LH50 March 2007 Part Number Pb-Free Marking MIC5216-2.5YMM MIC5216-3.3YMM MIC5216-5.0YMM MIC5216-2.5YM5 LH25 MIC5216-3.3YM5 LH33 MIC5216-3.6YM5 LH36 MIC5216-5.0YM5 LH50 2 Junction Voltage Package Temp. Range 2.5V –40° to +125°C 8-Pin MSOP 3.3V –40° to +125°C 8-Pin MSOP 5 ...
Page 3
... Ground: MSOP-8 pins 5 through 8 are internally connected. OUT Regulator Output EN Enable (Input): CMOS compatible control input. Logic high = enable; logic low or open = shutdown. FLG Error Flag (Output): Open-Collector output. Active low indicates an output undervoltage condition. 3 MIC5216 MIC5216-xxBM5/YM5 SOT-23-5 Fixed Voltages M9999-032307 ...
Page 4
... EN OUT V ≥ 3.0V 500mA EN OUT V ≤ 0. ≤ 0.18V EN Frequency = 120Hz OUT Note 50mA 2.2µF OUT OUT 4 MIC5216 )................................. 2.5V to 12V IN )..................................... ........................ –40°C to +125°C J ).......................................... Note 1 JA < +125°C, unless noted. J Min Typ Max Units – –2 2 ppm/°C 40 0.009 0.05 ...
Page 5
... FLAG , and the ambient temperature The maximum allowable power dissipation at any ambient temperature θ . Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the 12V for t = 10ms MIC5216 Min Typ Max Units 0 0.18 2.0 V 0.01 –1 µ ...
Page 6
... FREQUENCY (Hz) Noise Performance 10 10mA 1µF OUT 1 0.1 500mA Pending 0.01 0.001 OUT 0.0001 1E+11E+21E+3 1E+41E+5 1E+61E+7 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) 6 MIC5216 Power Supply Rejection Ratio -20 OUT -40 - 100mA -80 OUT C = 1µF OUT -100 1E+11E+21E+31E+41E+51E+61E+7 ...
Page 7
... Micrel, Inc. Block Diagram March 2007 MIC5216 Fixed Regulator with External Components 7 MIC5216 M9999-032307 ...
Page 8
... No-Load Stability The MIC5216 will remain stable and in regulation with no load (other than the internal voltage divider) unlike many other voltage regulators. This is especially important in CMOS RAM keep-alive applications. ...
Page 9
... This device will deliver 500mA start-up current from a SOT-23-5 or MM8 package, allowing high power from a very low profile device. The MIC5216 can subsequently provide output current that is only limited by the thermal characteristics of the device. You can obtain higher continuous currents from the device with the proper design ...
Page 10
... First, calculate the power dissipation of the device at 50mA. We will use the MIC5216-3.3BM5 with 5V input voltage as our example. P × 50mA = (5V – 3.3V) × 50mA + 5V × 650µA D ° ...
Page 11
... Micrel, Inc. ° Ambient Figure 3. MIC5216-x.xBMM (MSOP-8) on Minimum Recommended Footprint ° Ambient Figure 4. MIC5216-x.xBMM (MSOP- 1-inch The total power dissipation of the device under these conditions is the sum of the two power dissipation figures × 50mA + P × 500mA D(total 151mW + 119mW D(total 270mW ...
Page 12
... Micrel, Inc. Package Information March 2007 8-Pin MSOP (MM) SOT-23-5 (M5) 12 MIC5216 M9999-032307 ...
Page 13
... A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully March 2007 indemnify Micrel for any damages resulting from such use or sale. © 2000 Micrel, Incorporated. 13 MIC5216 M9999-032307 ...