RC0201JR-074K7L Yageo, RC0201JR-074K7L Datasheet - Page 6

• Manufacturer Part Number: RC0201JR-074K7L
• Description: RES 4.7K OHM 1/20W 5% 0201 SMD
• Manufacturer: Yageo
• Series: RC0201r

Specifications of RC0201JR-074K7L

• Temperature Coefficient: ±200ppm/°C
• Resistance (ohms): 4.7K
• Power (watts): 0.05W, 1/20W
• Composition: Thick Film
• Tolerance: ±5%
• Size / Dimension: 0.024" L x 0.012" W (0.60mm x 0.30mm)
• Height: 0.009" (0.23mm)
• Lead Style: Surface Mount (SMD - SMT)
• Package / Case: 0201 (0603 Metric)
• Resistance In Ohms: 4.70K
• Case: 0201 (0603 metric)
• Resistance: 4.7kohm
• Resistance Tolerance: ± 5%
• Power Rating: 50mW
• Voltage Rating: 25V
• Resistor Element Material: Thick Film
• Resistor Case Style: 0201
• No.: RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 311-4.7KNTR

TESTS AND REQUIREMENTS
Short time
overload
Board Flex/
Bending
Jul 15, 2008 V.4
TEST
Life/
Operational Life/
Endurance
High
Temperature
Exposure/
Endurance at
upper category
temperature
Moisture
Resistance
Thermal Shock
Table 4 Test condition, procedure and requirements
Chip Resistor Surface Mount
TEST METHOD
MIL-STD-202G-method 108A
IEC 60115-1 4.25.1
JIS C 5202-7.10
MIL-STD-202G-method 108A
IEC 60115-1 4.25.3
JIS C 5202-7.11
MIL-STD-202G-method 106F
IEC 60115-1 4.24.2
MIL-STD-202G-method 107G
MIL-R-55342D-para 4.7.5
IEC60115-1 4.13
IEC60115-1 4.33
PROCEDURE
1,000 hours at 70±5 °C applied RCWV
1.5 hours on, 0.5 hour off, still air required
1,000 hours at maximum operating temperature
depending on specification, unpowered
No direct impingement of forced air to the parts
Tolerances: 125±3 °C
Each temperature / humidity cycle is defined at 8
hours (method 106F), 3 cycles / 24 hours for 10d
with 25 °C / 65 °C 95% R.H, without steps 7a &
7b, unpowered
Parts mounted on test-boards, without
condensation on parts
Measurement at 24±2 hours after
test conclusion
-55/+125 °C
Note: Number of cycles required is 300. Devices
unmounted
Maximum transfer time is 20 seconds. Dwell time
is 15 minutes. Air – Air
2.5 times RCWV or maximum overload voltage
whichever is less for 5 sec at room temperature
Device mounted on PCB test board as described,
only 1 board bending required
3 mm bending
Bending time: 60±5 seconds
Ohmic value checked during bending
RC
SERIES
0201 (RoHS Compliant)
REQUIREMENTS
±(2%+0.05 Ω)
<100 mΩ for Jumper
±(1%+0.05 Ω)
<50 mΩ for Jumper
±(2%+0.05 Ω)
<100 mΩ for Jumper
±(0.5%+0.05 Ω) for 10 KΩ to
10 MΩ
±(1%+0.05 Ω) for others
<50 mΩ for Jumper
±(2%+0.05 Ω)
<50 mΩ for Jumper
No visible damage
±(1%+0.05 Ω)
<50 mΩ for Jumper
No visible damage
Product specification
www.yageo.com
6
8