TNPW04021K74BETD Vishay, TNPW04021K74BETD Datasheet - Page 7
![RES 1.74K OHM 1/16W 0.1% 0402](/photos/12/73/127361/541-0402__1005__tnpw_series_sml.jpg)
TNPW04021K74BETD
Manufacturer Part Number
TNPW04021K74BETD
Description
RES 1.74K OHM 1/16W 0.1% 0402
Manufacturer
Vishay
Series
TNPWr
Datasheet
1.TNPW06038K20BETA.pdf
(8 pages)
Specifications of TNPW04021K74BETD
Resistance (ohms)
1.74K
Power (watts)
0.063W, 1/16W
Composition
Thin Film
Temperature Coefficient
±25ppm/°C
Tolerance
±0.1%
Size / Dimension
0.039" L x 0.020" W (1.00mm x 0.50mm)
Height
0.014" (0.35mm)
Lead Style
Surface Mount (SMD - SMT)
Package / Case
0402 (1005 Metric)
Resistance In Ohms
1.74K
Case
0402 (1005 metric)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Features
-
Other names
TNPW0402 1K74 0.1% T9 RT7
www.vishay.com
72
TNPW
Vishay
TEST AND REQUIREMENTS
All tests are carried out in accordance with the following
specifications:
EN 60115-1, Generic specification (includes tests)
EN 140 400, Sectional specification (includes schedule for
qualification approval)
EN 140 401-801, Detail specification (includes schedule for
conformance inspection)
The following table contains only the most important tests.
For the full test schedule refer to the documents listed above.
The testing also covers most of the requirements specified
by EIA/IS-703 and JIS-C-5202. The tests are carried out in
accordance with IEC 60068 and under standard atmospheric
conditions in accordance with IEC 60068-1, 5.3. Climatic
category LCT/UCT/56 (rated temperature range: Lower
TEST PROCEDURES AND REQUIREMENTS
TEST
Endurance Test at 70 °C
IEC 60115-1 4.25.1
Endurance at UCT
IEC 60115-1 4.25.3
Overload Test
IEC 60115-1 4.13
Thermal Shock
IEC 60115-1 4.19, IEC 60068-2-14
Damp Heat Steady State
IEC 60115-1 4.24, IEC 60068-2-3
Resistance to Soldering Heat
IEC 60115-1 4.18, IEC 60068-2-20
APPLICABLE SPECIFICATIONS
• CECC40000/40400
• EN140400
• EIA 575
• EN 140401-801
• EN 60115-1
• IEC 60286-3
CONDITIONS OF TEST
1000 hours at 70 °C, 1.5 hours “ON”, 0.5 hours
“OFF”
1000 hours at 125 °C without load
Short time overload for 2 seconds
2.5 x rated voltage or ≤ 2 x limiting element voltage
Rapid change between upper and lower
category temperature
56 days at 40 °C and 93 % relative humidity
10 seconds at 260 °C solder bath temperature
For technical questions contact: ff3aresistors@vishay.com
≤ 0.05 % (1000 h rated power at 70 °C)
High Stability Thin Film Chip Resistor
Category Temperature, Upper Category Temperature; damp
heat, long term, 56 days) is valid. Unless otherwise specified
the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1 060 mbar).
The components are mounted for testing on boards in
accordance with EN 60115-1, 4.31 unless otherwise
specified. The parameters stated in the Test Procedures and
Requirements table are based on the required tests and
permitted limits of EN 140 401-801. However, some
additional tests and a number of improvements against those
minimum requirements have been included.
≤ ± 0.05 %
≤ ± 0.05 %
≤ ± 0.05 %
≤ ± 0.1 %
≤ ± 0.1 %
≤ ± 0.1 %
< 100R
± 0.1 %; ± 0.25 %
TNPW0402 TO TNPW2512
TEST RESULTS
TOLERANCES
≤ ± 0.05 %
≤ ± 0.05 %
≤ ± 0.02 %
≤ ± 0.02 %
≤ ± 0.05 %
≤ ± 0.02 %
≥ 100R
Document Number: 31006
Revision: 06-Jul-06
± 0.5 %; ± 1.0 %
≤ ± 0.25 %
≤ ± 0.5 %
≤ ± 0.1 %
≤ ± 0.1 %
≤ ± 0.5 %
≤ ± 0.1 %