MMF-25FRF100R Yageo, MMF-25FRF100R Datasheet - Page 6
![RES MELF MET 100 OHM 1/4W 1%](/photos/13/7/130767/mmp100frf100r_sml.jpg)
MMF-25FRF100R
Manufacturer Part Number
MMF-25FRF100R
Description
RES MELF MET 100 OHM 1/4W 1%
Manufacturer
Yageo
Series
MMFr
Datasheet
1.MMF25SFRF10R.pdf
(7 pages)
Specifications of MMF-25FRF100R
Resistance (ohms)
100
Power (watts)
0.25W, 1/4W
Composition
Metal Film
Temperature Coefficient
±100ppm/°C
Tolerance
±1%
Size / Dimension
0.087" Dia x 0.232" L (2.20mm x 5.90mm)
Lead Style
Surface Mount (SMD - SMT)
Package / Case
MELF, 0207
Resistance In Ohms
100
Case
MELF
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Height
-
(3) Solderability
(4) Resistance to Solvent
(5) Pulse Overload
(6) Load Life in Humidity
(7) Load Life Test
(8) Temperature Cycling Test
(9) Resistance to Soldering Heat
Immerse the specimen into the solder pot at 260 ± 5 °C for 5 ± 0.5 seconds.
At least 95% solder coverage on the termination.
The specimen into the appropriate solvent of IPA condition of ultrasonic machine for 1 minutes.
The specimen is no deterioration of coatings and color code.
Apply 4 times of rated voltage to the specimen at the 1 second on and 25 seconds off cycle, subjected
to voltage application cycles specified in 10,000 time。
The change of the resistance value shall be within ± 1.0% + 0.05 Ω
Place the specimen in a test chamber at 40 ± 2 °C and 90 ~ 95 % relative humidity. Apply the rated
voltage to the specimen at the 1.5 hours on and 0.5 hour off cycle. The total length of test is 1,000 hours
The change of the resistance value shall be within ± 2 % + 0.1 Ω
Placed in the constant temperature chamber of 70 ± 3 °C the resistor shall be connected to the lead wire
at the point of 25mm. Length with each terminal, the resistors shall be arranged not much effected
mutually by the temperature of the resistors and the excessive ventilation shall not be performed, for 90
minutes on and 30 minutes off under this condition the rated D.C. voltage is applied continuously for
1000+48/-0 hours then left at no-load for 1hour, measured at this time the resistance value。
The change of the resistance value shall be within ±2% + 0.1 Ω.
There shall be no remarkable change in the appearance and the color code shall be legible after the test.
The temperature cycle shown in the following table shall be repeated 5 times consecutively. The
measurement of the resistance value is done before the first cycle and after ending the fifth cycle,
leaving in the room temperature for about 1 hour。
Temperature Cycling Conditions:
The change of the resistance value shall be within ± 0.75 % + 0.05 Ω
After the test the resistor shall be free from the electrical or mechanical damage.
The terminal lead shall be dipped into the solder pot at 350 ± 10 °C for 3 ± 0.5 seconds up to 2 ~ 2.5 mm.
The change of the resistance value shall be within ± 0.5 % + 0.05 Ω
Step
1
2
3
4
Temperature(°C)
155 ± 3
-55 ± 3
25 ± 3
25 ± 3
Page-6
Time (minute)
2 ~ 3
2 ~ 3
30
30