FRM1WSJR-52-180R Yageo, FRM1WSJR-52-180R Datasheet
![RES FUSE METAL 180 OHM 1W 5%](/photos/13/81/138106/frm50sgr-52-12r_sml.jpg)
FRM1WSJR-52-180R
Specifications of FRM1WSJR-52-180R
Related parts for FRM1WSJR-52-180R
FRM1WSJR-52-180R Summary of contents
Page 1
... Headquarters: 3F, No.233-1, Pao Chiao Rd., Hsin Tien, Taipei, Taiwan, R.O.C. Tel: 886-2-2917-7555 Fax: 886-2-2917-4286 Hsin Tien Plant: 3F, No.5, Lane 560, Chung Cheng Rd., Hsin Tien Taipei, Taiwan, R.O.C Tel: 886-2-2218-2139 Fax: 886-2-6629-8898 for Fusible Type FRM series ±2% & ±5% URL: www.yageo.com Page-1 ...
Page 2
... Rev. Description 00 issue new spec. Description Metal Film Resistors, Fusible Type Series FRM Issue Date Drawn Jul 16, 2007 Sara Lin Rev. Page-2 Approved Joyce Chung 00 ...
Page 3
... PRODUCT: FLAME-PROOF METAL FILM FUSIBLE RESISTORS (Normal & Miniature Style) 2. PART NUMBER: Part number of the flame-proof metal film fusible resistor is identified by the name, power, tolerance, packing, temperature coefficient, special type and resistance value. The 5th color band is white to represent fusible resistors. ...
Page 4
BAND-CODE: COLOR 1ST BAND BLACK 0 BROWN 1 RED 2 ORANGE 3 YELLOW 4 GREEN 5 BLUE 6 VIOLET 7 GREY 8 WHITE 9 GOLD SILVER The Surface for Normal Size: (Grey color) The Surface for Miniature Size: (Pink ...
Page 5
ELECTRICAL CHARACTERISTICS Table I STYLE Power Rating at 70 ℃ Maximum Working Voltage Maximum Overload Voltage Dielectric Withstanding Voltage Resistance Range Operating Temp. Range ±200 ppm /℃ Temperature Coefficient * Below or over this resistance on request. 5. POWER ...
Page 6
... The resistor shall be able to withstand without breakdown or flashover. (4) Temperature Coefficient Test Test of resistors above room temperature 100°C ± 2°C ( Testing Temperature 115°C to 130° the constant temperature silicon plate for over minutes. Then measure the resistance value. The Temperature Coefficient is calculated by the following equation and its value should be within the range of requested ...
Page 7
... The specimen is no deterioration of coatings and color code. (8) Terminal Strength Direct Load – Resistors shall be held by one terminal and the load shall be gradually applied in the direction of the longitudinal axis of the resistor unit the applied load reacheds 5 pounds。 The load shall be held for 10 seconds. The load of weight shall be ≧ 2 24.5N ). ...
Page 8
The terminal lead shall be dipped into the solder pot at 350 ± 10 °C for 3 ± 0.5 seconds mm. The change of the resistance value shall be within ± 1 0.05 Ω 8. ...
Page 9
TAPE ON BOX PACKING STYLE Normal Miniature FRM-25 FRM50S FRM-50 FRM1WS FRM100 FRM2WS FRM200 FRM3WS 11. Plant Address A. Taiwan Hsin Tien Plant 3F, No.5, Lane 560, Chung Cheng Road, Hsin Tien Taipei, Taiwan, ROC ( 台北縣新店市中正路 560 巷 ...