LTC3728EUH Linear Technology, LTC3728EUH Datasheet - Page 22
![IC SW REG SYNC STP-DN DUAL 32QFN](/photos/6/59/65962/161-32-qfn_sml.jpg)
LTC3728EUH
Manufacturer Part Number
LTC3728EUH
Description
IC SW REG SYNC STP-DN DUAL 32QFN
Manufacturer
Linear Technology
Series
PolyPhase®r
Type
Step-Down (Buck)r
Datasheet
1.LTC3728EGPBF.pdf
(36 pages)
Specifications of LTC3728EUH
Internal Switch(s)
No
Synchronous Rectifier
Yes
Number Of Outputs
2
Voltage - Output
0.8 ~ 5.5 V
Current - Output
3A
Frequency - Switching
250kHz ~ 550kHz
Voltage - Input
3.5 ~ 36 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
32-WFQFN Exposed Pad
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC3728EUH
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC3728EUH
Manufacturer:
LT
Quantity:
20 000
Company:
Part Number:
LTC3728EUH#PBF
Manufacturer:
LINEAR
Quantity:
3
Part Number:
LTC3728EUH#TR
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIONS INFORMATION
LTC3728
Fault Conditions: Overcurrent Latchoff
The RUN/SS pins also provide the ability to latch off the
controller(s) when an overcurrent condition is detected. The
RUN/SS capacitor, C
the inrush current. After the controller has been started and
given adequate time to charge up the output capacitor and
provide full load current, the RUN/SS capacitor is used for
a short-circuit timer. If the regulator’s output voltage falls
to less than 70% of its nominal value after C
4.1V, C
output is in an overcurrent condition. If the condition lasts
for a long enough period, as determined by the size of the
C
be shut down until the RUN/SS pin voltage is recycled.
If the overload occurs during start-up, the time can be
approximated by:
If the overload occurs after start-up, the voltage on C
will begin discharging from the Zener clamp voltage:
This built-in overcurrent latchoff can be overridden by
providing a pull-up resistor to the RUN/SS pin, as shown
in Figure 7. This resistance shortens the soft-start period
and prevents the discharge of the RUN/SS capacitor during
an over current condition. Tying this pull-up resistor to
V
Why should you defeat overcurrent latchoff? During the
prototyping stage of a design there may be a problem
with noise pickup or poor layout, causing the protection
circuit to latch off. Defeating this feature will easily allow
22
SS
IN
t
t
LO2
LO1
(as in Figure 7) defeats overcurrent latchoff.
and the specifi ed discharge current, the controller will
SS
≈ [C
≈ [C
= 2.7 • 10
begins discharging on the assumption that the
SS
*OPTIONAL TO DEFEAT OVERCURRENT LATCHOFF
SS
Figure 7. RUN/SS Pin Interfacing
(6 – 3.5)]/(1.2μA) = 2.1 • 10
(4.1 – 1.5 + 4.1 – 3.5)]/(1.2μA)
3.3V OR 5V
6
SS
(C
, is used initially to turn on and limit
SS
)
D1
V
IN
R
SS
*
RUN/SS
C
SS
6
(C
3728 F07
SS
SS
reaches
)
SS
troubleshooting of the circuit and PC layout. The internal
short-circuit and foldback current limiting still remains
active, thereby protecting the power supply system from
failure. After the design is complete, a decision can be
made whether to enable the latchoff feature.
The value of the soft-start capacitor C
scaled with output voltage, output capacitance and load
current characteristics. The minimum soft-start capaci-
tance is given by:
The minimum recommended soft-start capacitor of
C
Fault Conditions: Current Limit and Current Foldback
The LTC3728 current comparator has a maximum sense
voltage of 75mV, resulting in a maximum MOSFET cur-
rent of 75mV/R
limit generally occurs with the largest V
ambient temperature—conditions that cause the highest
power dissipation in the top MOSFET.
The LTC3728 includes current foldback to help further
limit load current when the output is shorted to ground.
The foldback circuit is active even when the overload
shutdown latch previously described is overridden. If the
output falls below 70% of its nominal output level, then
the maximum sense voltage is progressively lowered from
75mV to 25mV. Under short-circuit conditions with very
low duty cycles, the LTC3728 will begin cycle skipping in
order to limit the short-circuit current. In this situation,
the bottom MOSFET will be dissipating most of the power
but less than in normal operation. The short-circuit ripple
current is determined by the minimum on-time t
of the LTC3728 (less than 200ns), the input voltage and
inductor value:
The resulting short-circuit current is:
SS
C
ΔI
I
SC
SS
= 0.1μF will be suffi cient for most applications.
L(SC)
=
> (C
R
25mV
= t
SENSE
OUT
ON(MIN)
)(V
SENSE
+
OUT
2
1
(V
. The maximum value of current
) (10
I
IN
L(SC)
/L)
–4
) (R
SENSE
SS
)
IN
may need to be
at the highest
ON(MIN)
3728fg