AS1331-BTDT-33-1K austriamicrosystems, AS1331-BTDT-33-1K Datasheet - Page 11

• Manufacturer Part Number: AS1331-BTDT-33-1K
• Description: IC CONV BUCK/BOOST 3.3V 10TDFN
• Manufacturer: austriamicrosystems
• Type: Step-Down (Buck), Step-Up (Boost)r

Specifications of AS1331-BTDT-33-1K

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 3.3V
• Current - Output: 300mA
• Voltage - Input: 1.8 ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Frequency - Switching: -
• Other names: AS1331-BTDT-33-1KTR

AS1331
Datasheet - D e t a i l e d D e s c r i p t i o n
Other AS1331 Features
Shutdown
The part is in shutdown mode while the voltage at pin EN is below 0.4V and is active when the voltage is higher than
1.4V.
Note: EN can be driven above V
Output Disconnect and Inrush Limiting
During shutdown V
current is also limited at turn-on mode to minimize the surge currents seen by the input supply. These features of the
AS1331 are realized by opening both P-channel MOSFETs of the rectifiers, allowing a true output disconnect.
Power-OK and Low-Battery-Detect Functionality
LBO goes low in startup mode as well as during normal operation if:
The LBI pin can be connected to a resistive-divider to monitor a particular definable voltage and compare it with a
1.25V internal reference. If LBI is connected to GND an internal resistive-divider is activated and connected to the
output. Therefore, the Power-OK functionality can be realised with no additional external components.
The Power-OK feature is not active during shutdown and provides a power-on-reset function that can operate down to
V
connect a pull-up resistor from pin LBO to pin VOUT. Larger values for this resistor will help to minimize current
consumption; a 100k Ω resistor is perfect for most applications
For the circuit shown in the left of
value resistor-divider networks while maintaining accuracy. Place the resistor-divider network as close to the device as
possible. Use a defined resistor for R
Where:
V
In case of the LBI pin is connected to GND, an internal resistor-devider network is activated and compares the output
voltage with a 92.5% voltage threshold. For this particular Power-OK application, no external resistive components are
necessary.
Thermal Shutdown
To prevent the AS1331 from short-term misuse and overload conditions the chip includes a thermal overload
protection. To block the normal operation mode all switches will be turned off. The device is in thermal shutdown when
the junction temperature exceeds 145°C. To resume the normal operation the temperature has to drop below 135°C.
A good thermal path has to be provided to dissipate the heat generated within the package. Otherwise it’s not possible
to operate the AS1331 at its useable maximal power. To dissipate as much heat as possible away from the package
into a copper plane with as much area as possible, it’s recommended to use multiple vias in the printed circuit board.
It’s also recommended to solder the Exposed Pad (pin 11) to the GND plane.
Note: Continuing operation in thermal overload conditions may damage the device and is considered bad practice.
www.austriamicrosystems.com/DC-DC_Buck-Boost/AS1331
IN
LBI
- The voltage at the LBI pin is below LBI threshold (1.25V). This can be used to monitor the battery voltage.
- LBI pin is connected to GND and V
= 1.8V. A capacitor to GND may be added to generate a power-on-reset delay. To obtain a logic-level output,
(the internal sense reference voltage) is 1.25V.
this case.
OUT
is going to 0V so that no current from the input source is running thru the device. The inrush
IN
Figure 24 on page
or V
5
and then calculate R
OUT
OUT
, as long as it is limited to less than 5.5V.
is below 92.5% of its nominal value. LBO works as a power-OK signal in
R
4
=
12, the input bias current into LBI is very low, permitting large-
R
Revision 1.04
5
⋅
⎛
⎝
4
---------- - 1
V
V
as:
LBI
IN
(see Figure 25 on page
–
⎞
⎠
12).
(EQ 1)
11 - 16