QSH-060-01-F-D-A Samtec Inc, QSH-060-01-F-D-A Datasheet - Page 2

• Manufacturer Part Number: QSH-060-01-F-D-A
• Description: CONN RECPT 120POS .020" SMT GOLD
• Manufacturer: Samtec Inc
• Series: QStrip® QSHr

Specifications of QSH-060-01-F-D-A

• Connector Type: Receptacle, Center Strip Contacts
• Number Of Positions: 120
• Pitch: 0.020" (0.50mm)
• Number Of Rows: 2
• Mounting Type: Surface Mount
• Features: Board Guide, Ground Bus (Plane)
• Contact Finish: Gold
• Contact Finish Thickness: Flash
• Mated Stacking Heights: 5mm, 8mm, 11mm, 16mm, 19mm, 25mm
• Height Above Board: 0.128" (3.25mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Series:
5.0 ENVIRONMENTAL
Revision: B
Date: 6/19/2008
Specification: PSQ-004
5.1 Thermal Aging per EIA-364-17
5.2 Cyclic Humidity per EIA-364-31
5.3 Thermal Shock per EIA-364-32
5.4 Mechanical Shock per EIA-364-27
QSH/QTH
5.1.1
5.1.2
5.1.3
5.1.4
5.1.5
5.1.6
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.3.1
5.3.2
5.3.3
5.3.4
5.4.1
5.4.2
High Speed Socket 0.5 mm pitch
No Evidence of Physical Damage seen --- PASS
Change in Contact LLCR not to exceed +15.0 milli-Ohms (L- plating) --- PASS
Change in Ground LLCR not to exceed +5.0 milli-Ohms (L- plating) --- PASS
Change in Contact LLCR After Thermal and Gas Tight not to exceed +15.0 milli-
Ohms (L- plating) --- PASS
Change in Ground LLCR After Thermal and Gas Tight not to exceed +5.0 milli-
Ohms (L- plating) --- PASS
Test Conditions
5.1.6.1 105 degrees C
5.1.6.2 300 hours
No Evidence of Physical Damage seen --- PASS
Insulation Resistance > 5000 Meg Ohms --- PASS
No evidence of Breakdown or Arcing when applying 750 VAC --- PASS
Change in LLCR not to exceed +15.0 milli-Ohms (L- plating) --- PASS
Test Conditions
5.2.5.1 Cyclic 25 degrees C to 65 degrees C for 240 hours, at 90% to 95% RH
5.2.5.2 Time Condition "B" (240 hours) for Method III, excluding sub-cycle 7A
No Evidence of Physical Damage seen --- PASS
Change in Signal LLCR not to exceed +15 mOhm --- PASS
Change in GND LLCR not to exceed +5 mOhm --- PASS
Test Conditions
5.3.4.1 # Thermal Cycles: 5
5.3.4.2 Hot Temperature: 85 degrees C +3 degrees C/-0 degrees C
5.3.4.3 Cold Temperature: -55 degrees C +0 degrees C/-3 degrees C
5.3.4.4 Dwell/Configuration: 30 Minutes, Mated and Mounted
5.3.4.5 Hot/Cold Transition Instantaneous
No Evidence of Physical Damage seen --- PASS
Test Conditions
5.4.2.1 Test Condition: Test Condition "A"
5.4.2.2 Peak Value: 50 G
5.4.2.3 Duration: 11.0 milliSec
5.4.2.4 Waveform: Half Sine
5.4.2.5 # Shocks/Direction 3 Shocks/3 Axes (18 total)
and 7B
Reviewed by: JET
Checked by: JET
Approved by: JET
Edited by: RAS
Product Specification
© 2008 Samtec, Inc.
Page 2