STEVAL-PCC011V1 STMicroelectronics, STEVAL-PCC011V1 Datasheet - Page 21
![BOARD DEM ETHERNET PHY ST802RT1B](/photos/37/57/375789/steval-pcc011v1_sml.jpg)
STEVAL-PCC011V1
Manufacturer Part Number
STEVAL-PCC011V1
Description
BOARD DEM ETHERNET PHY ST802RT1B
Manufacturer
STMicroelectronics
Type
LDO Controllers & Regulatorsr
Specifications of STEVAL-PCC011V1
Main Purpose
Interface, Ethernet Controller (PHY and MAC)
Embedded
No
Utilized Ic / Part
ST802RT1
Primary Attributes
100Base-FX
Secondary Attributes
MII, RMII
Interface Type
Ethernet
Operating Supply Voltage
3.3 V
Product
Power Management Development Tools
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
ST802RT1B
ST802RT1A, ST802RT1B
Table 11.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Jabber Detect
MF Preamble
Remote Fault
100BASE-T4
Suppression
RESERVED
RESERVED
RESERVED
RESERVED
100BASE-X
100BASE-X
Half Duplex
Half Duplex
Negotiation
Negotiation
Full Duplex
Full Duplex
Link Status
10BASE-T
10BASE-T
Capability
Bit name
Extended
complete
ABILITY
Ability
Auto-
Auto-
RN01 [0d01, 0x01]: Status register
0 -> PHY not able to perform 100BASE-T4
Fixed to 0
1 -> PHY able to perform full-duplex 100BASE-X
Fixed to 1, internally not used
1 -> PHY able to perform half-duplex 100BASE-X
Fixed to 1
1 -> PHY able to perform full-duplex 10BASE-T
Fixed to 1, internally not used
1 -> PHY able to perform half-duplex 10BASE-T
Fixed to 1
Not used
Not used
Not used
Not used
1 -> Accepts management frames with preamble suppressed
0 -> Doesn't accept management frames without preamble
Controlled by RN14 [1].
1 -> Auto-negotiation process completed, registers 4, 5, 6 are now
valid
0 -> Auto-negotiation process not completed
Active only if auto-negotiation is enabled, else 0
1 -> Remote fault condition detected
0 -> No remote fault condition detected
Set when link partner signals a remote fault condition (RN05 - bit
13) or a far-end-fault indicator was asserted. Latched, so the
occurrence of a remote fault causes the remote fault bit to become
set and remain set until it is cleared (by register read, if no more
fault is present).
1 -> PHY is able to perform auto-negotiation
Fixed to 1
1 -> Link is valid and established (either for 10 and 100 Mb/s)
0 -> Link is down
This bit is cleared at link failure and set after a register read if a
valid link is established
1 -> Jabber condition detected: transmission exceeded max
number of bytes
0 -> No jabber condition detected.
Set at jabber condition detection, cleared only after register read
(if no more jabber condition is present).
Working on 10Base-T only. Fixed to 0 in 100Base-X modes
1 -> extended register capabilities
Fixed to 1
Doc ID 17049 Rev 1
Description
Registers and descriptors description
Default
0
1
1
1
1
0
0
0
0
1
0
0
1
0
0
1
type
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
Type
21/58
LH
LH
LL
P
P
P
P
P
P
P
P
P
P
P
-
-