XBIB-U Digi International/Maxstream, XBIB-U Datasheet - Page 41

• Manufacturer Part Number: XBIB-U
• Description: BOARD USB ZIGBEE MOD PRO
• Manufacturer: Digi International/Maxstream

Specifications of XBIB-U

• Design Resources: XBIB-U Shematic
• Accessory Type: Interface Board
• For Use With/related Products: XBee and XBee Pro Radios
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

XBee/XBee‐PRO™ OEM RF Modules ‐ 802.15.4 ‐ v1.xAx [2007.05.031]
DL (Destination Address Low) Command
DN (Destination Node) Command
DP (Disassociation Cyclic Sleep Period) Command
EA (ACK Failures) Command
<Networking {Addressing}> The DL command is
used to set and read the lower 32 bits of the RF
module's 64-bit destination address. When com-
bined with the DH (Destination Address High)
parameter, it defines the destination address used
for transmission.
A module will only communicate with other mod-
ules having the same channel (CH parameter),
PAN ID (ID parameter) and destination address (DH + DL parameters).
To transmit using a 16-bit address, set the DH parameter to zero and the DL parameter less than
0xFFFF. 0x000000000000FFFF (DL concatenated to DH) is the broadcast address for the PAN.
Refer to the XBee/XBee-PRO Addressing section for more information.
<Networking {Identification}> The DN command
is used to resolve a NI (Node Identifier) string to
a physical address. The following events occur
upon successful command execution:
module with the matching NI (Node Identifier).
If there is no response from a modem within 200 msec or a parameter is not specified (left blank),
the command is terminated and an ‘ERROR’ message is returned.
<Sleep Mode (Low Power)>
NonBeacon Firmware
End Device - The DP command is used to set and
read the time period of sleep for cyclic sleeping
remotes that are configured for Association but
are not associated to a Coordinator. (i.e. If a
device is configured to associate, configured as a
Cyclic Sleep remote, but does not find a Coordi-
nator; it will sleep for DP time before reattempt-
ing association.) Maximum sleep period is 268
seconds (0x68B0). DP should be > 0 for NonBeacon systems.
<Diagnostics> The EA command is used to reset
and read the count of ACK (acknowledgement)
failures. This parameter value increments when
the module expires its transmission retries with-
out receiving an ACK on a packet transmission.
This count saturates at its maximum value.
Set the parameter to “0” to reset count.
© 2007 MaxStream, Inc.
1. DL and DH are set to the address of the
2. ‘OK’ is returned.
3. RF module automatically exits AT Command Mode.
AT Command: ATDP
Parameter Range: 1 - 0x68B0
Default Parameter Value:0x3E8
Related Commands: SM (Sleep Mode), SP
(Cyclic Sleep Period), ST (Time before Sleep)
Minimum Firmware Version Required: v1.x80
AT Command: ATEA
Parameter Range:0 - 0xFFFF
Minimum Firmware Version Required: v1.x80
AT Command: ATDL
Parameter Range: 0 - 0xFFFFFFFF
Default Parameter Value: 0
Related Commands: DH (Destination Address
High), CH (Channel), ID (PAN VID), MY (Source
Address)
AT Command: ATDN
Parameter Range: 20-character ASCII String
Minimum Firmware Version Required: v1.x80
Chapter 3 ‐ RF Module Configuration
[x 10 milliseconds]
(1000 decimal)
41