A24-HABUF-P5I Digi International/Maxstream, A24-HABUF-P5I Datasheet - Page 37
![no-image](/images/no-image-200.jpg)
A24-HABUF-P5I
Manufacturer Part Number
A24-HABUF-P5I
Description
2.4GHZ ANTENNA U.FL
Manufacturer
Digi International/Maxstream
Datasheet
1.A24-HASM-525.pdf
(69 pages)
Specifications of A24-HABUF-P5I
Antenna Type
Whip
Number Of Bands
1
Frequency
2.4GHz
Gain
2.1dBi
Termination
U.FL
Mounting Type
Bulkhead
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Vswr
-
Height (max)
-
Other names
A24-HABUF-P51
A24-HABUF-P51
Q3655966F
A24-HABUF-P51
Q3655966F
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
A24-HABUF-P5I
Manufacturer:
MXS
Quantity:
36
XBee®/XBee‐PRO® RF Modules ‐ 802.15.4 ‐ v1.xEx [2009.09.23]
AC (Apply Changes) Command
AI (Association Indication) Command
<AT Command Mode Options> The AC command
is used to explicitly apply changes to module
parameter values. ‘Applying changes’ means that
the module is re-initialized based on changes
made to its parameter values. Once changes are applied, the module immediately operates
according to the new parameter values.
This behavior is in contrast to issuing the WR (Write) command. The WR command saves parame-
ter values to non-volatile memory, but the module still operates according to previously saved val-
ues until the module is re-booted or the CN (Exit AT Command Mode) command is issued.
Refer to the “AT Command - Queue Parameter Value” API type for more information.
<Networking {Association}> The AI command is
used to indicate occurrences of errors during the
last association request.
Use the table below to determine meaning of the
returned values.
Returned Value (Hex) Association Indication
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
0x13
0xFF
© 2009 Digi Internatonal, Inc.
Successful Completion - Coordinator successfully started or End Device association complete
Active Scan Timeout
Active Scan found no PANs
Active Scan found PAN, but the Coordinator Allow Association bit is not set
Active Scan found PAN, but Coordinator and End Device are not configured to support beacons
Active Scan found PAN, but Coordinator ID (PAN ID) value does not match the ID of the End Device
Active Scan found PAN, but Coordinator CH (Channel) value does not match the CH of the End Device
Energy Scan Timeout
Coordinator start request failed
Coordinator could not start due to Invalid Parameter
Coordinator Realignment is in progress
Association Request not sent
Association Request timed out - no reply was received
Association Request had an Invalid Parameter
Association Request Channel Access Failure - Request was not transmitted - CCA failure
Remote Coordinator did not send an ACK after Association Request was sent
Remote Coordinator did not reply to the Association Request, but an ACK was received
after sending the request
[reserved]
Sync-Loss - Lost synchronization with a Beaconing Coordinator
Disassociated - No longer associated to Coordinator
RF Module is attempting to associate
AT Command: ATAC
Minimum Firmware Version Required: v1.xA0
AT Command: ATAI
Parameter Range: 0 - 0x13 [read-only]
Related Commands: AS (Active Scan), ID (PAN
ID), CH (Channel), ED (Energy Scan), A1 (End
Device Association), A2 (Coordinator
Association), CE (Coordinator Enable)
Minimum Firmware Version Required: v1.x80
37