DVK-PRM122 Laird Technologies, DVK-PRM122 Datasheet - Page 35
![DEV KIT PRM122](/photos/15/97/159706/landingpagelairdlt2510wire_sml.jpg)
DVK-PRM122
Manufacturer Part Number
DVK-PRM122
Description
DEV KIT PRM122
Manufacturer
Laird Technologies
Series
FlexRF™r
Type
Transceiver, FHSSr
Specifications of DVK-PRM122
Frequency
2.4GHz
Output Power
50 mW
Antenna
U.FL Coaxial
Silicon Manufacturer
Laird Technologies
Kit Application Type
Communication & Networking
Application Sub Type
Wireless Module
Features
Very Robust In The Presence Of Interference Global
Rohs Compliant
Yes
For Use With/related Products
PRM122
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DVK-PRM122
Manufacturer:
LAIRD
Quantity:
2
LT2510
Wireless Module
CONFIGURING
THE LT2510
32 www.lairdtech.com
COMMAND DESCRIPTIONS
Write Digital Outputs
The OEM Host issues this command to write both
digital output lines to particular states. These states will
be persistent unless overwritten by another enabled
function (such as Hop Frame).
Write PWM Output
The PWM output is a square wave with a 630.1uS
period. The PWM ratio is the ratio of the high pulse
time to the Low pulse time. A value of 0x00 will output
a continuous Low signal. A ratio of 0xFF will output a
continuous high signal. A ratio of 0x80 will put out a
repeating pulse of 315.05uS high and 315.05uS Low.
Set Max Power
The OEM Host issues this command to adjust the
maximum output power.
Max Power settings are typical and can vary by
2dBm. The maximum output power will never exceed
+21dBm for PRM110/111/120/121 or +17dBm for
PRM112/113/122/123.
EEPROM Byte Read
Upon receiving this command, a transceiver will respond
with the desired data from the EEPROM addresses
requested by the OEM Host.
EEPROM Byte Write
Upon receiving this command, a transceiver will write
the data byte to the specified address but will not echo it
back to the OEM Host until the EEPROM write cycle is
complete.
Vendor ID
This command is used to set the Vendor ID in the radios.
The Vendor ID is a one-time writable parameter which is not
able to be read back for security purposes. Radios with the
Vendor ID set will only communicate to other radios that
have Vendor ID set to the same value. Once the Vendor ID
is set it cannot be changed. Setting this value incorrectly
will result in a radio which will not be able to communicate
with other radios on the network. Setting the Vendor ID is
not necessary for the radios to operate and care should be
taken when using it. To see if the Vendor ID has been set
the OEM can issue the command <0xCC> <0xF2> <0x06>
<0xFF> <0xFF>. If the response is 0xFF 0xFF then VID has
not been set. If the response is 0x00 0x00, then the VID has
been set. Issuing the command <0xCC> <0xF2> <0x06>
<0xFF> <0xFF> will not set the Vendor ID.
Command:
Number of Bytes Returned:
Response:
Parameter Range:
<Digital Out>
Command:
Number of Bytes Returned:
Response:
Parameter Range:
<PWM Ratio> = 0x00 -0xFF, the ratio of the high pulse
Command:
Number of Bytes Returned:
Response:
Parameter Range:
<Max Power> PRM110/111/120/121
Command:
Number of Bytes Returned:
Response:
Parameter Range:
<Start>
<Length>
<Data>
Command:
Number of Bytes Returned:
Response:
Parameter Range:
<Start>
<Length>
<Data>
<Last byte> = Value of last byte written
Command:
Number of Bytes Returned:
Response:
Parameter Range:
<Vid_H>
<Vid_L>
<Value>
0xCC <Digital Out>
0xCC <0x24>
0xCC <Max Pwr>
<0xCC> <Start> <Length> <Data>
<Start> <Length> <Last byte>
<0xCC> <0xF2> <0x06> <Value>
<0xCC> <0x23>
<0xCC> <0x25><Max Pwr>
<0xCC> <0xC0> <Start> <Length>
<0xCC> <0xC1> <Start> <Length> <Data>
<0xCC> <0xF2> <0x06> <Vid_H> <Vid_L>
<0xCC> <0x24> <PWM Ratio>
= EEPROM address to begin writing at
= Length of data to be written
= Data to be written
= EEPROM address to begin reading at
= Length of data to be read
= Requested data
= 0x00-0xFF
= 0x00-0xFF
= If Vid is set the response will be 0x00
0x00: 21 dBm typical
0x01: 17 dBm typical
0x02: 14 dBm typical
0x03: 11 dBm typical
0x00. If Vid is not set the response will
be 0xFF 0xFF
= bit-1: GIO_1
= bit-0: GIO_0
versus the Low pulse for a single period.
2
2
2
4+
3
2
Laird Technologies
PRM112/113/122/123
0x00: 17dBm typical
0x01: 14 dBm typical
0x02: 11 dBm typical
0x03: 8 dBm typical