RFEVAL2-315 RF Solutions, RFEVAL2-315 Datasheet
RFEVAL2-315
Specifications of RFEVAL2-315
RFEVAL2-315R1
Related parts for RFEVAL2-315
RFEVAL2-315 Summary of contents
Page 1
... DS600-10 March ‘06 Description The RF Solutions RF600E, & RF600D are easy to use encoder and decoder I/C’s. They have been designed to achieve the maximum possible range from any radio / Infra Red transmitter receiver set. Unlike other encoder /decoder devices the RF600E/600D ...
Page 2
Encoder / Decoder Chipset RF Evaluation Boards, Transmitter Encoder RF600E Operational Description The RF600E is a simple device to use. As shown in the typical application circuits, it requires only the addition of input switches and RF ...
Page 3
Encoder / Decoder Chipset RF Evaluation Boards, Pin Descriptions Pin Name Number S0 1 Switch input Switch input Switch input Switch input 3 Vss 5 Ground reference connection ...
Page 4
... This data may be fed directly to a microcontroller or RS232 type driver circuit which may then be fed directly serial port. (An RS232 serial data output is provided on SA123 & RFEVAL2). Serial data is output continually whilst data is being received from the RF600E transmitter. i.e. this output is valid regardless of whether the RF600E encoder has been learnt to the RF600D decoder or not ...
Page 5
Encoder / Decoder Chipset RF Evaluation Boards, Serial Data Format Serial Data is sent as a stream of ASCII characters at 9.6K baud. The character format is 8 data bits with 1 stop bit, no parity. A ...
Page 6
Encoder / Decoder Chipset RF Evaluation Boards, Pin Descriptions Pin Name Number 1 OP3 2 OP4 Vcc 5 Vss 6 ECS 7 ECLK 8 EDAT LRN 11 SD1 12 LKIN 13 ...
Page 7
Encoder / Decoder Chipset RF Evaluation Boards, IN This is the data input to the decoder, it may be connected directly to the RF receiver module or IR receiver module. LRN This input is used to set ...
Page 8
Encoder / Decoder Chipset RF Evaluation Boards, SLEEP Holding this pin high will causes the device to run normally. Holding this pin low will causes the device to enter a sleep mode where the current drain will ...
Page 9
Encoder / Decoder Chipset RF Evaluation Boards, RF600D Application Circuit – Stand Alone operation Status LED Vcc Learn Switch RF Receiver This circuit provides a complete decoding solution capable of learning unique encoders DS600-10 ...
Page 10
Encoder / Decoder Chipset RF Evaluation Boards, RF600D Application Circuit – With External EEPROM Vcc RF Receiver This circuit provides a complete decoding solution capable of learning unique encoders A complete ‘ready to operate’ ...
Page 11
Encoder / Decoder Chipset RF Evaluation Boards, Technical Specifications: Absolute Maximum Ratings Item Supply voltage Input voltage Output voltage Max output current Storage temperature Lead soldering temp ESD rating Note: Stresses above those listed under “Absolute Maximum ...
Page 12
Encoder / Decoder Chipset RF Evaluation Boards, Ordering Information Part Number RF600E RF600E-SO RF600DR6 RF600DR6-SO RF600D8R6 RF600D-SO8R6 RF600DP8 / RF600DS8 The Decoder is available as a miniature 8 pin version option providing a serial data output only. ...
Page 13
Encoder / Decoder Chipset RF Evaluation Boards, DS600-10 March ‘06 ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Page 13 ...
Page 14
Encoder / Decoder Chipset RF Evaluation Boards, DS600-10 March ‘06 ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Page 14 ...
Page 15
Encoder / Decoder Chipset RF Evaluation Boards, DS600-10 March ‘06 ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Page 15 ...
Page 16
Encoder / Decoder Chipset RF Evaluation Boards, Tel +44 (0)1273 898 000 All Trademarks acknowledged and remain the property of the respected owners. Information contained in this document is believed to be accurate, however no representation or ...
Page 17
... Uses RF600 Encoder/Decoder (Keeloq) The RFEVAL2 / 3 are hardware development platforms designed to assist the engineer with the design of a remote telemetry application. This kit provides several projects. Each project utilises an ‘off the shelf’ transmitter encoder incorporating the RF600E. The RFEVAL receiver board use s the RF600D to perform reception and decoding providing a variety of outputs. Our aim with this Evaluation kit is to assist the engineer in achieving a remote telemetry application with ...
Page 18
... RF Evaluation Boards, Description The RFEVAL2 kit uses the RF600 chip set to implement the highly secure KeeLoq protocol and allows the user to experiment with this code hopping system. The kit is supplied primarily as a hardware development platform which obviates the need to construct hand-wired prototype boards which are rarely successful in creating a valid environment for the development of radio systems ...
Page 19
... AM radio transmitter circuit. Three push buttons allow the user to send commands to the RFEVAL2 board where the signals will be received and decoded. The RFEVAL2 board is supplied with a circuit diagram and also a parts list and can be used for a wide range of development tasks including the following. ...
Page 20
... HRR3 RF600 Decoder Circuit. The RF600 decoder stage of the RFEVAL2 board is implemented using the RF600D chip. This device offers a complete ‘system on a chip’ solution to radio data reception, Keeloq decoding and non volatile memory handling. Examination of the circuit diagram and layout reveals that U1, the RF600D device pin part which can be either in a DIL or a surface mount package ...
Page 21
Encoder / Decoder Chipset RF Evaluation Boards, Input data mark. The data stream received by the RF600D chip may be inverted as it passes through the radio or IR path. When the bit stream is generated by ...
Page 22
Encoder / Decoder Chipset RF Evaluation Boards, Infra Red Input Circuit. The Infra Red (IR) input stage consists solely of the IS436 IR detector device. This part is constructed pin package with integral lens ...
Page 23
Encoder / Decoder Chipset RF Evaluation Boards, Typical Application Upto 48 Transmitters Configuring the outputs to operate with Transmitter Encoders The principle of operation is as previously described in the operation of the RF600D. Note that the ...
Page 24
... Time from Encoder Switch depressed to Decoder output Time from Encoder Switch release to Decoder output Ordering Information Part Number RFEVAL2-315R1 Evaluation Kit including all components to operate 315MHz RFEVAL2-433R2 Evaluation Kit including all components to operate 433MHz Evaluation Kit PCB Assemvbly only (includes all circuitry except RF Modules, ...