ATR2820-DEV-BOARD2 Atmel, ATR2820-DEV-BOARD2 Datasheet
ATR2820-DEV-BOARD2
Specifications of ATR2820-DEV-BOARD2
Related parts for ATR2820-DEV-BOARD2
ATR2820-DEV-BOARD2 Summary of contents
Page 1
... ATR2820 RF Demo Board plus USB RF Interface Board 1. Required Items • ATR2820 RF Demo Board • USB RF Interface Board • PC with USB Port Cables and ATR2820 Software Installed Power Supply (9V/500 mA) • Spectrum Analyzer ( GHz) • Signal Generator ( GHz) • Oscilloscope (100 MHz Bandwidth Recommended) 2. Set-up ...
Page 2
... Using jumper 12 enables to select several TX data pattern '1-0' sequences and a PRBS pattern. Since the ATR2820 is in closed loop mode, low frequency '1-0' patterns will be canceled by the PLL. These patterns are no problem for the open loop mode, which is used during normal burst mode operation. ...
Page 3
... RX Mode - USB RF Interface Board Jumper Setting Figure 4-1. RX Mode - USB RF Interface Board Jumper Setting 9178A–DECT–03/10 Evaluation Board for ATR2820 3 ...
Page 4
... Figure 4-2. Example of RX Data Output Signal with PRBS Modulation Evaluation Board for ATR2820 4 9178A–DECT–03/10 ...
Page 5
... Figure 5-1. Data Generator Output 9178A–DECT–03/10 Evaluation Board for ATR2820 Select TX data rate Pseudo random pattern for feeding TX data Bit patterns sequence for feeding TX data 5 ...
Page 6
... The output of the reference oscillator produces a rectangular signal with a level between 0V and V_RF. The signal level can be adjusted with a potentiometer R4 ( alternative the potentiometer can be shorted with JP4. Evaluation Board for ATR2820 6 Supplies the power to the T280X demo board (the regulated output voltage and current can be measured at the jumper ...
Page 7
... Next, a new window stating “Add New Hardware Wizard” opens up. Click “Next”. Figure 6-1. Choose “Search for the best driver for your device (Recommended)” and click “Next”. Figure 6-2. 9178A–DECT–03/10 Evaluation Board for ATR2820 ® Windows Window “Add New Hardware Wizard” Window “Add New Hardware Wizard” 2 ® ...
Page 8
... Check “Specify location” and “browse” to the folder where the driver files are stored (CD or download folder). Then click “Next”. Figure 6-3. In the next window (AVR309:USB to UART protocol converter ...) click “Next”. Figure 6-4. Evaluation Board for ATR2820 8 Window “Add New Hardware Wizard” 3 Window “Add New Hardware Wizard” 4 9178A–DECT–03/10 ...
Page 9
... Verify the device “AVR309:USB to UART protocol converter ...” is present in “Start - Settings -Control Panel - System - Device Manager - Universal Serial Bus controllers”. Figure 6-6. The device has been successfully installed. 9178A–DECT–03/10 Evaluation Board for ATR2820 Window “Add New Hardware Wizard” 5 Window “System Properties” 9 ...
Page 10
... Figure 6-7. A window indicating “Found New Hardware Wizard” opens up. Choose “’Install from a list or specify location (Advanced)” and click “Next”. Figure 6-8. Evaluation Board for ATR2820 10 Window “Found New Hardware” Window “Found New Hardware Wizard” ® ...
Page 11
... Then click “Next”. Figure 6-9. A new window indicating AVR309:USB to UART protocol converter ...) appears. Figure 6-10. Window “AVR309:USB to UART protocol converter” 9178A–DECT–03/10 Evaluation Board for ATR2820 Window “Please choose your search and installation options.” 11 ...
Page 12
... If a window with the warning message “Hardware Installation” appears, choose “Continue Anyway”. Figure 6-11. Window “Hardware Installation” Windows will then install the necessary driver files and performs system changes. Figure 6-12. Window “Please wait while the wizard installs the software” Evaluation Board for ATR2820 12 9178A–DECT–03/10 ...
Page 13
... The installation is now complete. Click “Finish”. Figure 6-13. Window “Completing the Found New Hardware Wizard” After successful installation, a small window with an installation confirmation appears. Figure 6-14. Window “Confirmation of Installation” 9178A–DECT–03/10 Evaluation Board for ATR2820 13 ...
Page 14
... Verify if the device “AVR309:USB to UART protocol converter ...” is present in “Start - Set- tings - Control Panel - System - Device Manager - Universal Serial Bus controllers”. Figure 6-15. Window “Device Manager” The device has been successfully installed. Evaluation Board for ATR2820 14 9178A–DECT–03/10 ...
Page 15
... Appendix C: ATR2820 Control Software Installation The ATR2820 control software supports Microsoft 2000 and Windows XP. Your computer must be switched on and running Microsoft Start the setup.exe file from the CD. Figure 7-1. Window “Start the setup.exe File” Figure 7-2. Confirm this dialog box by clicking OK. ...
Page 16
... Start the installation by clicking on the installation symbol. Figure 7-3. Figure 7-4. Allow to set up a new program group by clicking “weiter”. Evaluation Board for ATR2820 16 Window “ATR2820_USB-Setup” 2 Window “ATR2820_USB-Setup” 3 9178A–DECT–03/10 ...
Page 17
... The Installation has been successfully completed. Click on “OK”. Figure 7-5. 9178A–DECT–03/10 Evaluation Board for ATR2820 Window “ATR2820_USB-Setup” ...
Page 18
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...