ADRF6604-EVALZ Analog Devices Inc, ADRF6604-EVALZ Datasheet - Page 3

• Manufacturer Part Number: ADRF6604-EVALZ
• Description: EVAL KIT FOR ADRF6604
• Manufacturer: Analog Devices Inc
• Type: Mixer, Downconversionr

Specifications of ADRF6604-EVALZ

• Frequency: 2.5GHz ~ 2.9GHz
• For Use With/related Products: ADRF6604
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SPECIFICATIONS
RF SPECIFICATIONS
VCCx = 5 V, ambient temperature (T
using CDAC = 0xC and IP3SET = 3.3 V, unless otherwise noted.
Table 2.
Parameter
INTERNAL LO FREQUENCY RANGE
RF INPUT FREQUENCY RANGE
RF INPUT AT 2360 MHz
RF INPUT AT 2560 MHz
RF INPUT AT 2760 MHz
IF OUTPUT
LO INPUT/OUTPUT (LOP, LON)
Input Return Loss
Input P1dB
Second-Order Intercept (IIP2)
Third-Order Intercept (IIP3)
Single-Sideband Noise Figure
LO-to-IF Leakage
Input Return Loss
Input P1dB
Second-Order Intercept (IIP2)
Third-Order Intercept (IIP3)
Single-Sideband Noise Figure
LO-to-IF Leakage
Input Return Loss
Input P1dB
Second-Order Intercept (IIP2)
Third-Order Intercept (IIP3)
Single-Sideband Noise Figure
LO-to-IF Leakage
Voltage Conversion Gain
IF Bandwidth
Output Common-Mode Voltage
Gain Flatness
Gain Variation
Output Swing
Output Return Loss
Frequency Range
Output Level (LO as Output)
Input Level (LO as Input)
Input Impedance
A
) = 25°C, f
Test Conditions/Comments
±3 dB RF input range
Relative to 50 Ω (can be improved with external match)
−5 dBm each tone (10 MHz spacing between tones)
−5 dBm each tone (10 MHz spacing between tones)
IP3SET = 3.3 V
IP3SET = open
At 1× LO frequency, 50 Ω termination at the RF port
Relative to 50 Ω (can be improved with external match)
−5 dBm each tone (10 MHz spacing between tones)
−5 dBm each tone (10 MHz spacing between tones)
IP3SET = 3.3 V
IP3SET = open
At 1× LO frequency, 50 Ω termination at the RF port
Low-side injection
Relative to 50 Ω (can be improved with external match)
−5 dBm each tone (10 MHz spacing between tones)
−5 dBm each tone (10 MHz spacing between tones)
IP3SET = 3.3 V
IP3SET = open
At 1× LO frequency, 50 Ω termination at the RF port
Differential 200 Ω load
Small-signal 3 dB bandwidth
External pull-up balun or inductors required
Over frequency range, any 5 MHz/50 MHz
Over full temperature range
Differential 200 Ω load
Relative to 200 Ω
Externally applied 1× LO input, internal PLL disabled
1× LO into a 50 Ω load, LO output buffer enabled
REF
= 38.4 MHz, f
Rev. 0 | Page 3 of 24
PFD
= 38.4 MHz, high-side LO injection, f
Min
2500
1200
250
IF
Typ
−22
14.8
53.5
28.0
15.4
14.0
−44.3
−22
14.8
56.3
27.5
15.6
14.3
−41.9
−20
14.8
66.0
27.1
16.0
14.7
−41.2
6.3
500
5
0.2/1.0
1.0
2
−15
−8.7
±6
50
= 140 MHz, IIP3 optimized
Max
2900
3600
6000
ADRF6604
Unit
MHz
MHz
dB
dBm
dBm
dBm
dB
dB
dBm
dB
dBm
dBm
dBm
dB
dB
dBm
dB
dBm
dBm
dBm
dB
dB
dBm
dB
MHz
V
dB
dB
V p-p
dB
MHz
dBm
dBm
Ω