CC-EVB-900W Copeland Communications Inc, CC-EVB-900W Datasheet
CC-EVB-900W
Specifications of CC-EVB-900W
Related parts for CC-EVB-900W
CC-EVB-900W Summary of contents
Page 1
... Features ? Supports all CCI Modems and Radios ? RS-232,TTL Digital Serial and USB Host Interfaces ? On-board modem status indicators ? Internal 3.3 and 5 volt modem power supply on PC Eval board Description The wireless modem evaluations kit allows for complete evaluation and field testing of the wireless modems, antennas and the users application ...
Page 2
... STEP 1: Install the USB drivers from the enclosed CDROM. When you see the warning below, simply click “Continue anyway”. The installer is intended for Windows 2000, NT and XP. Contact CCI for Windows 98, Linux or Macintosh drivers. Wireless Modem Evaluation Board User’s Guide © ...
Page 3
STEP 2: Connect the RS-232 Serial Cable to the Evaluation Board and then the PC serial port. Wireless Modem Evaluation Board User’s Guide Figure 2 Serial Connection to PC © 2005 Copeland Communications, Inc. Internet: www.copelandcommunications.com Subject to technical changes ...
Page 4
... STEP 3: Connect the USB Adapter Board with attached wireless modem to the remote PC using a standard USB cable. The USB interface and wireless module are powered by the USB interface. The CC-USB adapter allows you to connect any 3.3V Copeland Communications module to a USB port. ...
Page 5
STEP 4: Copeland Communications ships all evaluation kits with the modems populated on the board already. To reinsert a removed modem or to exchange for another, be sure to connect pin 1 of the module to pin 1 of the ...
Page 6
STEP 5: Set the power jumper to 3.3V. The wireless modem supplied with the eval kit is a 3.3 volt ONLY device. WARNING power input on the Radio WILL cause permanent damage. WARNING: Only place ONE jumper for ...
Page 7
STEP 6: Connect the power supply to the board and to the wall outlet. At this point you should see the POWER LED lit. Note that there is no power switch on the Evaluation Board. WARNING: Be sure to remove ...
Page 8
... STEP 7: In Windows™, start HyperTerminal. (Start->Accessories->HyperTerminal). connection and select the COM port connected to the Evaluation Kit. If you have both Radios connected to the same computer, start a new session of HyperTerminal and repeat the process for the second Radio (you will have two HyperTerminal sessions going at the same time when your done). To determine the COM port for the USB Radio, look under USB in the Device Manager. Wireless Modem Evaluation Board User’ ...
Page 9
... Step 2: Set the channels on both Radios so they match: at.cl=00 (set group ID) Step 3: Dial the other modem using the ATDT command Atdt000002 If the command is successful, you will get “CONNECT” as the response. Wireless Modem Evaluation Board User’s Guide Figure 9 © 2005 Copeland Communications, Inc. ...
Page 10
Using Local IO pins There are three commands to control the local IO pins. Direction (ATLD), Read (ATLI) and Write (ATLO). To set the direction of a pin, simply send the ATLD<pin number>=[0,1]: ATLD2=1 - Sets IO pin 2 up ...
Page 11
... Note: There are no buffers or drivers between the Socket Module and the evaluation board connectors. This provides the user direct electrical access to all the signals on the Socket Module. RS-232 Interface The user can select the RS-232 by installing the RS-232 Select Jumpers on JP3 (Labeled ‘SERIAL I/F SELECT’ on Rev 1 of the PCB) ...
Page 12
QUICK STATE GUIDE Your evaluation board is delivered configured for RS-232 serial operation. Modem (Default configuration – RS-232 19.2KBPS N81) RS-232 mode selected Target Voltage set to 3.3 volts Modem Settings Wireless Modem Evaluation Board User’s Guide Option Serial I/F ...
Page 13
Mechanical The evaluation board is designed to support the entire family of Copeland Communications modules. These modules are designed on a dual in line package (DIP) configuration with 24mm row spacing and 2mm pin pitch. Wireless Modem Evaluation Board User’s ...
Page 14
Schematic Wireless Modem Evaluation Board User’s Guide © 2005 Copeland Communications, Inc. Internet: www.copelandcommunications.com Subject to technical changes ...
Page 15
... European/Asian Version (230 VAC) Wireless modems w/ MMCX antennas Please call factory Wireless Modem Evaluation Board User’s Guide Table 2 © 2005 Copeland Communications, Inc. Internet: www.copelandcommunications.com Subject to technical changes CCI Order Number CC-900W-EVAL CC-900W-CA EVAL-None CC-USB Add suffix – 230 VAC -MMCX ...