FCTN-RLY4-433-2 Linx Technologies Inc, FCTN-RLY4-433-2 Datasheet - Page 4

• Manufacturer Part Number: FCTN-RLY4-433-2
• Description: MODULE 4 RELAY RECEIVER 433MHZ
• Manufacturer: Linx Technologies Inc

Specifications of FCTN-RLY4-433-2

• Function: Receiver, Relay
• Modulation Or Protocol: ASK, OOK
• Frequency: 433MHz
• Applications: General Remote Control, Garage Opener, RKE
• Interface: Receiver, Latched Output
• Sensitivity: -112dBm
• Data Rate - Maximum: 1.2 kbps
• Features: 4 Latched Outputs, Dual Power Inputs
• Voltage - Supply: 5 V ~ 16 V
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: FCTN-RLY4-433; FCTN-RLY4XX-433; FCTN-RLY4XX-433

LABELING REQUIREMENTS
Page 6
In cases where the FCTN-RLY4-***-2 module is incorporated inside a product
and its standard labeling is not visible, the end product must be labeled as shown
below.
• The following label shall be affixed in a conspicuous location to any device
• When the device is constructed in two or more sections connected by wires
• The label shall not be a stick-on paper label. The label shall be “permanently
self-certified under the FCC’s Declaration of Conformity process:
and marketed together, the label is required to be affixed only to the main
control unit.
affixed” to the device (meaning the label is etched, engraved, stamped, silk-
screened, indelibly printed on a permanently attached part of the device, or
on a nameplate fastened to the equipment by welding, riveting, or a
permanent adhesive). The label must be designed to last the expected
lifetime of the equipment in the environment in which the equipment may be
operated and may not be readily detachable.
Trade Name
Model Number
COMPLIANCE REQUIREMENTS
Place the above statement in the instruction manual or insert card.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with FCC regulations, shielded cables must be
used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception.
The user is cautioned that changes and modifications made to the equipment
without the approval of manufacturer could void the user’s authority to operate
this equipment.
The FCTN-RLY4-***-2 has been tested by an FCC-approved facility and been
found to comply with all applicable FCC and Industry Canada requirements as of
the date of this document. A Declaration of Conformity (DoC) is on file. It is the
user’s responsibility to consult the FCC or other testing body to determine if any
additional testing may be required on the user’s completed product. In products
where no additional testing is required, further labeling of the unit is not needed
unless the module will be placed inside another housing. It is, however,
necessary to include the following statement in the end product’s instruction
manual or insert card.
Page 7
Page 7