FCTN-RLY4-433-2 Linx Technologies Inc, FCTN-RLY4-433-2 Datasheet - Page 4
![MODULE 4 RELAY RECEIVER 433MHZ](/photos/14/16/141642/fctn-rly4xx-433_sml.jpg)
FCTN-RLY4-433-2
Manufacturer Part Number
FCTN-RLY4-433-2
Description
MODULE 4 RELAY RECEIVER 433MHZ
Manufacturer
Linx Technologies Inc
Specifications of FCTN-RLY4-433-2
Function
Receiver, Relay
Modulation Or Protocol
ASK, OOK
Frequency
433MHz
Applications
General Remote Control, Garage Opener, RKE
Interface
Receiver, Latched Output
Sensitivity
-112dBm
Data Rate - Maximum
1.2 kbps
Features
4 Latched Outputs, Dual Power Inputs
Voltage - Supply
5 V ~ 16 V
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
FCTN-RLY4-433
FCTN-RLY4XX-433
FCTN-RLY4XX-433
FCTN-RLY4XX-433
FCTN-RLY4XX-433
LABELING REQUIREMENTS
Page 6
In cases where the FCTN-RLY4-*** module is incorporated inside a product and
its standard labeling is not visible, the end product must be labeled as shown
below.
• The following label shall be affixed in a conspicuous location to any device
• When the device is constructed in two or more sections connected by wires
• When the device is so small, or for such use that it is not practical to place
• The label shall not be a stick-on paper label. The label shall be “permanently
previously self-certified under the FCC’s Declaration of Conformity process,
when the product is authorized based on assembly using separately
authorized components and the resulting product does not require additional
testing:
and marketed together, the label is required to be affixed only to the main
control unit.
the statement on the unit itself, the information shown on the label shall be
placed in a prominent location in the instruction manual or pamphlet supplied
to the user or, alternatively, shall be placed on the container in which the
device is marketed. However, the unique FCC logo, device trade name, and
model number must be present on the device.
affixed” to the device (meaning the label is etched, engraved, stamped, silk-
screened, indelibly printed on a permanently attached part of the device, or
on a nameplate fastened to the equipment by welding, riveting, or a
permanent adhesive). The label must be designed to last the expected
lifetime of the equipment in the environment in which the equipment may be
operated and may not be readily detachable.
Assembled From Tested Components
(Complete System Not Tested)
Trade Name
Model Number
COMPLIANCE REQUIREMENTS
Place the above statement in the instruction manual or insert card.
INSTRUCTION TO THE USER
This device complies with Part 15 of the FCC Rules.
Operation of this device is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a Class B
computing device, pursuant to FCC Rules. In order to maintain compliance with
FCC regulations, shielded cables must be used with this equipment. Operation
with non-approved equipment or unshielded cables is likely to result in
interference to radio and TV reception. The user is cautioned that changes and
modifications made to the equipment without the approval of manufacturer
could void the user’s authority to operate this equipment.
The FCTN-RLY4-*** has been tested by an FCC-approved facility and been
found to comply with all applicable FCC and Industry Canada requirements as of
the date of this document. A Declaration of Conformity (DoC) is on file. It is the
user’s responsibility to consult the FCC or other testing body to determine if any
additional testing may be required on the user’s completed product. In products
where no additional testing is required, further labeling of the unit is not needed
unless the module will be placed inside another housing. It is, however,
necessary to include the following statement in the end product’s instruction
manual or insert card.
Page 7
Page 7