X24-019PKC-U Digi International/Maxstream, X24-019PKC-U Datasheet - Page 25
![no-image](/images/no-image-200.jpg)
X24-019PKC-U
Manufacturer Part Number
X24-019PKC-U
Description
MODEM RF 2.4GHZ 19.2KBPS USB
Manufacturer
Digi International/Maxstream
Series
XStream™r
Specifications of X24-019PKC-U
Function
Transceiver, Modem
Modulation Or Protocol
FHSS
Frequency
2.4GHz ~ 2.4835GHz
Applications
General Purpose
Interface
USB
Sensitivity
-102dBm
Power - Output
17dBm (50mW)
Data Rate - Maximum
20 kbps
Voltage - Supply
5V
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
XStream‐PKG‐U™ USB RF Modem – Product Manual v4.2B5 [2006.02.27]
PW (Pin Wake-up) Command
RE (Restore Defaults) Command
RN (Delay Slots) Command
RO (Packetization Timeout) Command
<Sleep (Low Power)> Under normal operation, a
modem in Cyclic Sleep Mode cycles from an
active state to a low-power state at regular
intervals until data is ready to be received. If the
PW Parameter is set to 1, the SLEEP/DI3 Pin can
be used to awaken the modem from Cyclic Sleep.
If the SLEEP Pin is de-asserted (low), the modem
will be fully operational and will not go into Cyclic
Sleep. Once SLEEP is asserted, the modem will
remain active for the period of time specified by
ST (Time before Sleep) Command, and will return
to Cyclic Sleep Mode (if no data is ready to be
transmitted). PW Command is only valid if Cyclic
Sleep has been enabled.
<Diagnostics> RE Command restores all
configurable parameters to factory default
settings. However, RE Command will not write
the default values to non-volatile (persistent) memory. Unless the WR (Write) Command is issued
after the RE command, the default settings will not be saved in the event of modem reset or
power-down.
<Networking> RN Command is only applicable if
retries have been enabled [RR (Retries)
Command], or if forced delays will be inserted
into a transmission [refer to the TT (Streaming
Limit) Command]. RN Command is used to adjust
the time delay that the transmitter inserts before
attempting to resend a packet. If the transmitter
fails to receive an acknowledgement after
sending a packet, it will insert a random number
of delay slots (ranging from 0 to (RN minus 1))
before attempting to resend the packet. Each delay slot lasts for a period of 38ms.
If two modems attempted to transmit at the same time, the random time delay after packet
failure would allow one of the two modems to transmit the packet successfully, while the other
would wait until the channel opens up to begin transmission.
<Serial Interfacing> RO Command is used to
specify/read the time of silence (no bytes
received) after which transmission begins. After a
serial byte is received and if no other byte is
received before the RO timeout, the transmission
will start.
© 2006 MaxStream, Inc. Confidential and Proprietary
AT Command: ATPW
Binary Command: 0x1D (29 decimal)
Parameter Range: 0 – 1
Default Parameter Value: 0
Number of bytes returned: 1
Related Commands: SM (Sleep Mode), ST (Time
before Sleep)
Minimum Firmware Version Required: 4.22
AT Command: ATRE
Binary Command: 0x0E (14 decimal)
AT Command: ATRN
Binary Command: 0x19 (25 decimal)
Parameter Range: 0 – 0xFF [slots]
Default Parameter Value: 0 (no delay slots
inserted)
Number of bytes returned: 1
Related Commands: RR (Retries), TT
(Streaming Limit)
Minimum Firmware Version Required: 4.22
AT Command: ATRO
Binary Command: 0x21 (33 decimal)
Parameter Range: 0 – 0xFFFF [x 200 µs]
Default Parameter Value: 0
Number of bytes returned: 2
Minimum Firmware Version Required: 4.2AA
Parameter
Value
0
1
Configuration
Disabled
Enabled
25