CMD-HHTX-433 Linx Technologies Inc, CMD-HHTX-433 Datasheet - Page 4
![XMITTER HANDHELD 433MHZ 8 BUTTON](/photos/14/16/141687/cmd-hhtx_series_sml.jpg)
CMD-HHTX-433
Manufacturer Part Number
CMD-HHTX-433
Description
XMITTER HANDHELD 433MHZ 8 BUTTON
Manufacturer
Linx Technologies Inc
Datasheet
1.CMD-HHTX-315.pdf
(5 pages)
Specifications of CMD-HHTX-433
Function
Transmitter
Modulation Or Protocol
ASK, OOK
Frequency
433MHz
Applications
General Remote Control, Garage Opener, RKE
Interface
Handheld, 8 Button
Data Rate - Maximum
1.2 kbps
Features
8 Buttons, 1000 ft. Operating Distance
Voltage - Supply
2.1 V ~ 3.6 V
Package / Case
Handheld Transmitter
Board Size
85.1 mm x 46 mm x 15.7 mm
Minimum Operating Temperature
- 30 C
Supply Voltage (min)
2.1 V
Product
RF Modules
Maximum Frequency
433.92 MHz
Supply Voltage (max)
3.6 V
Maximum Operating Temperature
+ 70 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
Sensitivity
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
RECEIVERS
TYPICAL APPLICATIONS
Page 6
There are four options for receivers within the Linx
product line. The first option is to use one of the OEM
Function Modules, such as the Relay Module or the AC
Wall Module. These items are also pre-certified and
can be immediately included in a product.
The other options are to use one of the Linx receiver
modules. The signal sent by the OEM Handheld
transmitter can be received by the LR Series receiver
module or the LT Series transcever module. These
modules can be connected to the Holtek HT658
decoder to decode the signal, or a custom
microcontroller can be programmed to decode it and
take specific action.
The KH2 Series offers a slightly simpler solution by
combining the LR Series receiver and the HT658
decoder in a single package.
When a button is pressed on the transmitter, a
corresponding line on the decoder will go high (as long
as the addresses match). This can then be connected
to whatever circuitry is required by the application.
Application Note AN-00300 discusses in detail how to
set the addresses on all of the units. Data guides for all
of the receivers, the HT640 encoder, and the HT658
decoder can be found on the Linx Technologies
website, www.linxtechnologies.com.
The outstanding sensitivity of the
LR Series receiver offers the best
range
Handheld transmitter. When using
the LR Series receiver, the Holtek
HT658 decoder chip should be
used to decode the received signal.
This decoder has ten address lines
that must match the transmitter
address lines. A DIP switch is
commonly used to set these, but
they can also be hardwired. If the
address lines match, when a button
on the transmitter is pressed a
corresponding data line on the
decoder (D0-D7) will go high.
These data lines can then be
connected to external circuitry to
perform
required by the application.
when
whatever
used
function
with
the
is
Figure 6: LR Receiver and HT658 Schematic
VCC
R1
390k
GND
GND
1
2
3
4
5
6
7
8
10
11
12
RXM-LR
1
2
3
4
5
6
7
8
9
NC
NC
NC
GND
VCC
PDN
RSSI
DATA
HT658
D1
D2
D3
D4
D5
D6
D7
VT
DIN
OSC1
OSC2
GND
VCC
D0
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
ANT
GND
NC
NC
NC
NC
NC
NC
24
23
22
21
20
19
18
17
16
15
14
13
16
15
14
13
12
11
10
9
VCC
GND
GND
Figure 7: CMD-HHTX-*** Schematic
Page 7