RX6000 RFM, RX6000 Datasheet
RX6000
Specifications of RX6000
Available stocks
Related parts for RX6000
RX6000 Summary of contents
Page 1
... The RX6000 employs RFM’s amplifier-sequenced hybrid (ASH) architecture to achieve this unique blend of characteristics. All critical RF functions are contained in the hybrid, simplifying and speeding design-in. The RX6000 is sensitive and stable. A wide dynamic range log detector, in combination with digital AGC and a compound data slicer, provide robust performance in the presence of on-channel interference or noise ...
Page 2
... Maximum Units dB dB µA 3.7 Vdc mV 10 P-P 85 ° Inches Min Nom Max .389 .395 .400 .265 .270 .275 .070 .076 .080 .065 .070 .075 .015 .020 .025 .035 .040 .045 .125 .130 .135 .055 .060 .065 Page RX6000 - 4/7/08 ...
Page 3
... K ±1%, typical values 160 K ±5% K ±5% 4.7 µF tantalum 27 pF ±5% NPO ohm antenna 100 nH 50 ohm antenna R TH1 R 12 TH2 THLD 2 RREF 11 R REF GND2 10 LPF ADJ 9 R LPF Data Output Notes Page RX6000 - 4/7/08 ...
Page 4
... ASH Receiver Theory of Operation Introduction RFM’s RX6000 series amplifier-sequenced hybrid (ASH) receivers are specifically designed for short-range wireless control and data communication applications. The receivers provide robust operation, very small size, low power consumption and low implementation cost. All critical RF functions are contained in the hybrid, simplifying and speeding design-in ...
Page 5
... Otherwise, significant edge jitter will be added to the detected data pulse. RX6000 Series ASH Receiver Block Diagram Figure 2 is the general block diagram of the RX6000 series ASH receiver. Please refer to Figure 2 for the following discussions. Antenna Port The only external RF components needed for the receiver are the antenna and its matching components ...
Page 6
... Vdc. The BBOUT-CMPIN coupling-capacitor is then DC stabilized in 3 time constants (3*t BBC stable receiver operation for power supply rise time is 3*t PR BBC can be adjusted PW1 ). The total turn-on time to Page RX6000 - 4/7/08 ...
Page 7
... LPF in kilohms user selected LPF in µ user selected BBO is given kilohms set PW2 is in kilohms PW , where f is LPF LPF = 1.21*R , where LPF Notes PKD Page RX6000 - 4/7/08 ...
Page 8
... BBO PKD and 1.5* t PKA For this case: MAX BBO LPF from 4.5 kHz to 1.8 MHz. LPF is in kHz LPF AGC AGH with variations PKA for internal BBO and BBC between this pin and and 1.3* f LPF LPF Page RX6000 - 4/7/08 ...
Page 9
... RF amplifier). The ON pulse width t PW2 - 18.6, where µs and R PW1 PW1 PW to RREF. The threshold is TH1 can be adjusted between 0.1 and PRI is given by kilohms is in kilohms with a resistor R to ground (the ON pulse PW1 kilohms TH2 from start-to-start PRC PW1 is given by: PW Page RX6000 - 4/7/08 ...
Page 10
... E-mail: info@rfm.com ©2008 by RF Monolithics, Inc. .435 0.000 Dimensions in inches. SM-20H PCB Pad Layout Note: Specifications subject to change without notice. .370 .345 .305 .265 .225 .185 .145 .105 .09 .065 RX6000 - 4/7/08 Page ...