RFRXD0920T-I/LQ Microchip Technology, RFRXD0920T-I/LQ Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
RFRXD0920T-I/LQ
Manufacturer Part Number
RFRXD0920T-I/LQ
Description
IC RCVR 868/915MHZ ASK/FSK32LQFP
Manufacturer
Microchip Technology
Datasheet
1.RFRXD0420-ILQ.pdf
(32 pages)
Specifications of RFRXD0920T-I/LQ
Package / Case
32-LQFP
Frequency
800MHz ~ 930MHz
Sensitivity
-106dBm
Data Rate - Maximum
80 kbps
Modulation Or Protocol
ASK, FM, FSK
Applications
Home Automation, Remote Sensing, RKE
Current - Receiving
9.2mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Voltage - Supply
2.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Operating Supply Voltage
3.3 V, 5 V
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Memory Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
3.2
Figure 3-9 illustrates an example ASK applications cir-
cuit.
The IF Limiting Amplifier with RSSI is used as an ASK
detector. The RSSI signal is post detector filtered and
then compared to a reference voltage to determine if
the incoming RF signal is a logical one or zero. The
reference voltage can be configured as a dynamic
voltage level determined by the incoming RF signal
strength or by a predetermined fixed level.
3.2.1
The RSSI signal is low-passed filtered to remove high
frequency and pulse noise to aid the decision making
process of the comparator and increase the sensitivity
of the receiver. The RSSI signal low-pass filter is a RC
filter created by the RSSI output impedance of 36 kΩ
and capacitor C1. Setting the time constant (RC = τ) of
the RC filter depends on the signal period and when the
signal decision will be made.
3.2.1.1
Optimum sensitivity of the receiver with reasonable
pulse distortion occurs when the RC filter time constant
is between 1 and 2 times the signal period. If the time
constant of the RC filter is set too short, there is little
noise filtering benefit. However, if the time constant of
the RC filter is set too long, the data pulses will become
elongated causing inter-symbol interference.
3.2.1.2
If the bit decision occurs in the center of the signal
period (such as K
times the RC filter time constant should be set at less
than or equal to half the signal period. Figure 3-10 illus-
trates this method. The top trace represents the
received on-off keying (OOK) signal. The bottom trace
shows the RSSI signal after the RC low-pass filter.
FIGURE 3-10: CENTER SIGNAL PERIOD
2003 Microchip Technology Inc.
RSSI Signal
OOK Signal
RSSI POST DETECTOR FILTERING
Amplitude Shift Keying (ASK)
Signal Decision
Signal Period
DECISION RSSI LOW-PASS
FILTERED
EE
L
OQ
decoders), then one or two
Signal Decision
1τ to 2τ
Signal Period
Preliminary
If the bit decision occurs near the end of the signal
period, then the time constant should be set at less
than or equal to the signal period. Figure 3-11
illustrates this method.
Once the signal decision time and time period of the
signal period are known, then capacitor C1 can be
selected. Once C1 is selected, the designer should
observe the RSSI signal with an oscilloscope and
perform operational and/or bit error rate testing to
confirm receiver performance.
FIGURE 3-11: NEAR END OF THE SIGNAL
3.2.2
The internal operational amplifier is configured as a
comparator. The RSSI signal is applied to OPA+ (Pin
20) and compared with a reference voltage on OPA-
(Pin 19) to determine the logic level of the received
signal. The reference voltage can be dynamic or static.
The choice of dynamic versus static reference voltage
depends in part on the ratio of logical ones versus
zeros of the data (this can also be thought of as the AC
content of the data). Provided the ratio has an even
number of logical ones versus zeros, a dynamic refer-
ence voltage can be generated with a simple low-pass
filter. The advantage of the dynamic reference voltage
is the increased receiver sensitivity compared to a fixed
reference voltage. However, the comparator will output
random data. The decoder (for example, a pro-
grammed PICmicro MCU or K
distinguish between random noise and valid data.
The choice of a static reference voltage depends in part
on the DC content of the data. That is, the data has an
uneven number of logical ones versus zeros. The
disadvantage of the static reference voltage is
decreased receiver sensitivity compared to a dynamic
reference voltage. In this case, the comparator will
output data without random noise.
RSSI Signal
OOK Signal
COMPARATOR
rfRXD0420/0920
PERIOD DECISION RSSI LOW-
PASS FILTERED
Signal Decision
EE
L
Signal Period
1τ to 2τ
OQ
DS70090A-page 15
decoder) must