SI4738-C40-GM Silicon Laboratories Inc, SI4738-C40-GM Datasheet - Page 23
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
SI4738-C40-GM
Manufacturer Part Number
SI4738-C40-GM
Description
IC RX FM/WB RADIO 20UQFN
Manufacturer
Silicon Laboratories Inc
Datasheet
1.SI4737-C-EVB.pdf
(42 pages)
Specifications of SI4738-C40-GM
Frequency
520kHz ~ 1.71MHz, 64MHz ~ 108MHz, 162.4MHz ~ 162.55MHz
Modulation Or Protocol
AM, FM, WB
Applications
General Purpose
Current - Receiving
19.9mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Features
RSSI Equipped
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-20°C ~ 85°C
Package / Case
20-UQFN, 20-µQFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Sensitivity
-
Memory Size
-
Data Rate - Maximum
-
Lead Free Status / Rohs Status
Supplier Unconfirmed
5.7. Stereo Audio Processing
The output of the FM demodulator is a stereo
multiplexed (MPX) signal. The MPX standard was
developed in 1961, and is used worldwide. Today's
MPX signal format consists of left + right (L+R) audio,
left – right (L–R) audio, a 19 kHz pilot tone, and
RDS/RBDS data as shown in Figure 13 below.
5.7.1. Stereo Decoder
The Si4736/37/38/39's integrated stereo decoder
automatically decodes the MPX signal using DSP
techniques. The 0 to 15 kHz (L+R) signal is the mono
output of the FM tuner. Stereo is generated from the
(L+R), (L–R), and a 19 kHz pilot tone. The pilot tone is
used as a reference to recover the (L–R) signal. Output
left and right channels are obtained by adding and
subtracting the (L+R) and (L–R) signals respectively.
The Si4731 uses frequency information from the 19 kHz
stereo pilot to recover the 57 kHz RDS/RBDS signal.
5.7.2. Stereo-Mono Blending
Adaptive noise suppression is employed to gradually
combine the stereo left and right audio channels to a
mono (L+R) audio signal as the signal quality degrades
to maintain optimum sound fidelity under varying
reception conditions. Stereo/mono status can be
monitored with the FM_RSQ_STATUS command. Mono
operation
FM_BLEND_MONO_THRESHOLD property.
5.8. De-emphasis
Pre-emphasis and de-emphasis is a technique used by
FM broadcasters to improve the signal-to-noise ratio of
FM receivers by reducing the effects of high-frequency
interference and noise. When the FM signal is
transmitted, a pre-emphasis filter is applied to
accentuate
Si4736/37/38/39 incorporates a de-emphasis filter
which attenuates high frequencies to restore a flat
frequency response. Two time constants are used in
various regions. The de-emphasis time constant is
programmable to 50 or 75 µs and is set by the
FM_DEEMPHASIS property.
0
Mono Audio
Left + Right
Figure 13. MPX Signal Spectrum
the
can
15
Stereo
Pilot
19
high
Frequency (kHz)
23
be
audio
Stereo Audio
Left - Right
forced
38
frequencies.
with
53
RBDS
RDS/
57
The
the
Rev. 1.0
5.9. Stereo DAC
High-fidelity stereo digital-to-analog converters (DACs)
drive analog audio signals onto the LOUT and ROUT
pins. The audio output may be muted. Volume is
adjusted digitally with the RX_VOLUME property.
5.10. Soft Mute
The soft mute feature is available to attenuate the audio
outputs and minimize audible noise in very weak signal
conditions. The softmute attenuation level is adjustable
using the FM_SOFT_MUTE_MAX_ATTENUATION and
AM_SOFT_MUTE_MAX_ATTENUATION properties.
5.11. RDS/RBDS Processor
The Si4737/39 implements an RDS/RBDS* processor
for symbol decoding, block synchronization, error
detection, and error correction.
The Si4737/39 device is user configurable and provides
an optional interrupt when RDS is synchronized, loses
synchronization, and/or the user configurable RDS
FIFO threshold has been met.
The Si4737/39 reports RDS decoder synchronization
status and detailed bit errors in the information word for
each RDS block with the FM_RDS_STATUS command.
The range of reportable block errors is 0, 1–2, 3–5, or
6+.
corresponding block information word contains six or
more non-correctable errors or that the block checkword
contains errors.
*Note: RDS/RBDS is referred to only as RDS throughout the
5.12. Tuning
The tuning frequency is directly programmed using the
FM_TUNE_FREQ, WB_TUNE_FREQ, and
AM_TUNE_FREQ commands. The Si4736/37/38/39
supports channel spacing steps of 10 kHz in FM mode,
25 kHz in WB mode, and 1 kHz in AM mode.
More
remainder of this document.
(Si4737/39 Only)
Si4736/37/38/39-C40
than
six
errors
indicates
that
the
23