UPG2415TK-E2-A CEL, UPG2415TK-E2-A Datasheet
UPG2415TK-E2-A
Specifications of UPG2415TK-E2-A
Related parts for UPG2415TK-E2-A
UPG2415TK-E2-A Summary of contents
Page 1
DESCRIPTION μ The PG2415TK is a GaAs MMIC SPDT (Single Pole Double Throw) switch for 0.5 to 6.0 GHz applications, including dual-band wireless LAN. This device operates with dual control switching voltages of 2.7 to 5.3 V. This device can ...
Page 2
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM (Top View) RF1 GND RF2 TRUTH TABLE ON Path V 1 cont RFC-RF1 High RFC-RF2 Low ABSOLUTE MAXIMUM RATINGS (T Parameter Symbol Switch Control ...
Page 3
ELECTRICAL CHARACTERISTICS (T = +25° 3 cont (H) cont (L) specified) Parameter Symbol Insertion Loss 1 L ins Insertion Loss 2 L ins Insertion Loss 3 L ins Insertion Loss 4 L ins Isolation 1 ...
Page 4
EVALUATION CIRCUIT C1 RF1 RF2 C1 Note C1 : 0.5 to 2.0 GHz 2.0 to 6.0 GHz 000 pF The application circuits and their parameters are for reference only and are not ...
Page 5
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD RF1 1 OUT 2 OUT RF2 SW USING THE NEC EVALUATION BOARD Symbol Test Conditions 0.5 to 2.0 GHz f = 2.0 to 6.0 GHz ...
Page 6
TYPICAL CHARACTERISTICS (T capacitors = 8 pF, unless otherwise specified) RFC-RF1/RF2 INSERTION LOSS vs. FREQUENCY 0.0 V cont (H) –0.2 DC blocking capacitors = 56 pF –0.4 –0.6 –0.8 –1.0 –1 –1.4 –1.6 –1.8 –2.0 0.0 1.0 2.0 ...
Page 7
RFC RETURN LOSS vs. SWITCH CONTROL VOLTAGE (H) 0 –5 – 6.0 GHz –15 –20 –25 2.0 GHz –30 –35 –40 2.0 2.5 3.0 3.5 4.0 Switch Control Voltage (H) V cont (H) RFC-RF1/RF2 INSERTION LOSS, I vs. ...
Page 8
MOUNTING PAD LAYOUT DIMENSIONS 6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm) Remark The mounting pad layout in this document is for reference only. 8 0.26 0.48 0.48 Data Sheet PG10793EJ01V0DS μ PG2415TK ...
Page 9
PACKAGE DIMENSIONS 6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm) (Top View) Remark Dimension (Bottom View) 1.1±0.1 0.2±0.1 0.9±0 1.3±0. bigger than dimension (dimension Data Sheet PG10793EJ01V0DS μ PG2415TK ...
Page 10
RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Peak temperature (package surface temperature) Time at peak ...
Page 11
The information in this document is current as of February, 2010. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets, etc., for the most up-to-date specifications of ...
Page 12
This product uses gallium arsenide (GaAs). Caution GaAs Products GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. • Follow related laws and ordinances when disposing of the product. If ...