XT09-SI-MESH Digi International, XT09-SI-MESH Datasheet - Page 15

• Manufacturer Part Number: XT09-SI-MESH
• Description: MODULE RF 900MHZ 1W 115K W/RPSMA
• Manufacturer: Digi International

Specifications of XT09-SI-MESH

• Frequency: 900MHz
• Modulation Or Protocol: FHSS, FSK
• Power - Output: 1W
• Sensitivity: -100dBm
• Voltage - Supply: 2.8 V ~ 5.5 V
• Current - Receiving: 80mA
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Memory Size: -
• Data Interface: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 602-1183

XTend™ RF Module ‐ Product Manual v2.x6x
In order to enter Sleep Mode, one of the following conditions must be met (in addition to the mod-
ule having a non-zero SM parameter value):
When in Sleep Mode, the module will not transmit or receive data until the module first transitions
to Idle Mode. All Sleep Modes are enabled and disabled using SM Command. Transitions into and
out of Sleep Modes are triggered by various mechanisms as shown in the table below.
Table 2‐01. Summary of Sleep Mode Configurations
The SM (Sleep Mode) command is central to setting all Sleep Mode configurations. By default,
Sleep Modes are disabled (SM = 0) and the module remains in Idle/Receive Mode. When in this
state, the module remains constantly ready to respond to serial or RF activity.
Refer to the ‘Hardware Sleep’ section of the ‘Shutdown Mode’ section [previous page] to enable the
module's lowest power-consuming state (5 µA typical power-down current).
Pin Sleep (SM = 1)
This mode is voltage level activated. When the SLEEP pin is asserted, the module will finish any
transmitting or receiving activity; enter Idle Mode; then enter a state of sleep. When in Pin Sleep
Mode, the module will not respond to serial or RF activity.
After enabling Pin Sleep, the SLEEP pin controls whether the module is active or sleeping. When
SLEEP is de-asserted, the module is fully operational. When SLEEP is asserted, the module transi-
tions to Sleep Mode and remains in its lowest power-consuming state until the pin is de-asserted.
This pin is only active if the module is setup to operate in this mode; otherwise the pin is ignored.
Once in Pin Sleep, CTS (GPO1) is de-asserted (high), indicating that data should not be sent to the
module. The PWR pin is also de-asserted (low) when the module is in Pin Sleep Mode.
Note: The module will complete a transmission or reception before activating Pin Sleep.
Serial Port Sleep (SM = 2)
Serial Port Sleep is a Sleep Mode in which the module runs in a low power state until serial data is
detected on the DI pin.
Sleep Mode
(Setting)
Pin Sleep
(SM = 1)
Serial Port Sleep
(SM = 2)
Cyclic Sleep
(SM = 4 - 8)
1.
2.
© 2010 Digi Internatonal, Inc.
• Pin/Host-controlled
• Typical power-down current: < 147 µA
• Wake on serial port activity
• Typical power-down current: < 10 mA
The module is idle (no data transmission or reception) for the amount of time defined by
the ST (Time before Sleep) parameter. [NOTE: ST is only active when SM = 4-5.]
SLEEP (pin 8) is asserted (only for the ‘Pin Sleep’ option).
Transition into
Sleep Mode
Assert (high) SLEEP pin - A micro
controller can shut down and wake
modules via the SLEEP pin.
Note: The module will complete a
transmission or reception before
activating Pin Sleep.
Automatic transition to Sleep Mode
occurs after a user-defined period of
inactivity (no transmitting or receiving of
data).
Period of inactivity is defined by the ST
(Time before Sleep) Command.
RF module transitions in and out of Sleep Mode in cycles (user-selectable
wake-up interval of time is set using the SM command). The cyclic sleep
interval of time must be shorter than the interval of time that is defined by the
LH (Wake-up Initializer TImer) command.
Note: The module can be forced into Idle Mode using the SLEEP pin if the PW
(Pin Wake-up) command is issued.
Transition out of Sleep
Mode (wake)
De-assert (low) SLEEP pin
When a serial byte is received on
the DI pin
Related
Commands
(SM)
(SM), ST
(SM), ST, HT,
LH, PW
Power
Consumption
< 147 µA
< 10 mA
< 1.6 mA
when sleeping
(SM=4, 1 sec.,
@120K baud)
15