XC09-009PKC-UA Digi International/Maxstream, XC09-009PKC-UA Datasheet - Page 6

• Manufacturer Part Number: XC09-009PKC-UA
• Description: MODEM RF 900MHZ USB 9600 W/ACC
• Manufacturer: Digi International/Maxstream
• Series: 9XCite™r

Specifications of XC09-009PKC-UA

• Frequency: 900MHz
• Data Rate - Maximum: 9.6kbps
• Modulation Or Protocol: FHSS, FSK
• Power - Output: 6dBm
• Sensitivity: -108dBm
• Voltage - Supply: 2.85 V ~ 5.5 V
• Current - Receiving: 45mA
• Current - Transmitting: 55mA
• Data Interface: Connector, USB
• Antenna Connector: RP-SMA
• Operating Temperature: 0°C ~ 70°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Memory Size: -

9XCite‐PKG‐U™ USB RF Modem – Product Manual v2.1 [2007.01.04]
Figure 1‐02. Front View
Figure 1‐03. Back View
1‐02a.
Reset Switch
power is available through the USB Port
(> 500 mA).
* NOTE: Disconnect the USB cable before
connecting or removing power from the
Power Connector [1‐02d]. This port does
not require power unless insufficient
1.4. External Interface
1‐02a.
I/O & Power LEDs
1‐02b.
RSSI LEDs (all green)
1‐02b.
Config Switch
1‐02c. USB port
1‐02c.
Antenna Port
© 2007 MaxStream, Inc.
1‐02d. Power
Connector
1-02a. I/O & Power LEDs
1-02b. RSSI LEDs
1-02c. USB Port
1-02d. Power Connector*
1-03a. Reset Switch
1-03b. Config (Configuration) Switch
1-03c. Antenna Port
LEDs indicate modem activity as follows:
RSSI LEDs indicate the amount of fade margin present in an active
wireless link. Fade margin is defined as the difference between the
incoming signal strength and the modem's receiver sensitivity.
Standard Type-B USB connector - This port can also be used to power
the XCite-PKG-U unit.
5-12 VDC Power Connector - Power can also be supplied through the
VBUS pin of the USB port.
Pressing the Reset Switch forces the modem into reset (or re-boot). It
can be used in conjunction with the Configuration Switch [below] to
enter the RF modem into AT Command Mode by doing the following:
Simultaneously press the "Reset" and "Config" switches down, then
release the "Reset" button, then after 1 second release the "Config
button.
After these steps are taken, the RF modem enters into AT Command
Mode at the modem's default baud rate.
The Configuration Switch provides an alternate way to enter AT Com-
mand Mode. To enter AT Command Mode at the RF modem's default
baud rate, read the Reset Switch entry [above].
This port is a 50 Ohm RF signal connector for connecting to an RPSMA
(Reverse Polarity SMA) type antenna.
Yellow (top LED) = Serial Data Out (to host)
Green (middle) = Serial Data In (from host)
Red (bottom)
powered; it pulses on/off briefly during RF transmission.)
3 LEDs ON
2 LEDs ON
1 LED ON
0 LED ON
= Very Strong Signal (> 30 dB fade margin)
= Strong Signal (> 20 dB fade margin)
= Moderate Signal (> 10 dB fade margin)
= Weak Signal (< 10 dB fade margin)
= Power/TX Indicator (Red light is on when