ZMN2430-R RFM, ZMN2430-R Datasheet - Page 4
![MODULE ZIGBEE 2.4GHZ ROUTER](/photos/14/22/142203/zmn2430-r_sml.jpg)
ZMN2430-R
Manufacturer Part Number
ZMN2430-R
Description
MODULE ZIGBEE 2.4GHZ ROUTER
Manufacturer
RFM
Series
ZMNr
Specifications of ZMN2430-R
Frequency
2.4GHz
Data Rate - Maximum
250kbps
Modulation Or Protocol
802.15.4
Applications
ZigBee™
Power - Output
18dBm
Sensitivity
-95dBm
Voltage - Supply
3.3 V ~ 5.5 V
Current - Receiving
33mA
Current - Transmitting
130mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Wireless Frequency
2.4 GHz
Interface Type
SPI, UART
Modulation
DSSS, OQPSK
Operating Voltage
2.7 VDC to 5.5 VDC
Output Power
1 mW
Operating Temperature Range
- 40 C to + 85 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
CC2430
Other names
583-1024
ZMN2430 I/O Pad Descriptions
Pad
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
2
3
4
5
6
7
8
9
SPI_SCLK
UART_RX
SPI_MISO
SPI_MOSI
UART_TX
ADC REF
/RESET
SPI_EN
GPIO0
GPIO4
GPIO5
PWMA
GPIO2
GPIO1
GPIO3
PWMB
RSVD
RSVD
ADCX
ADCY
Name
ADCZ
RFIO
GND
GND
GND
GND
GND
VCC
NC
NC
Power supply and signal ground. Connect to the host circuit board ground.
Reserved pin. Leave unconnected.
Reserved pin. Leave unconnected.
Configurable digital I/O port 0. When configured as an output, the power-on state is also configurable.
Serial data output from UART.
Serial data input to UART.
Configurable digital I/O port 4. When configured as an output, the power-on state is also configurable.
Configurable digital I/O port 5. When configured as an output, the power-on state is also configurable.
Pulse-width modulated output A with internal low-pass filter. Provides a DAC function.
Configurable digital I/O port 2. When configured as an output, the power-on state is also configurable.
Configurable digital I/O port 1. When configured as an output, the power-on state is also configurable.
Configurable digital I/O port 3. When configured as an output, this high current port can sink up to 20 mA. The
power-on output state is also configurable.
Pulse-width modulated output B with internal low-pass filter. Provides a DAC function.
Power supply input, +3.3 to +5.5 Vdc.
Power supply and signal grounds. Connect to the host circuit board ground.
Power supply and signal grounds. Connect to the host circuit board ground.
Active low module hardware reset. Hold this input low when the power supply input is less than 2.7 Vdc.
7-bit to 12-bit ADC input 0. ADC full scale reading can be referenced to the module’s +3.3 V regulated suppy or
to the ADC’s internal +2.5 V reference.
7-bit to 12-bit ADC input 1. ADC full scale reading can be referenced to the module’s +3.3 V regulated suppy or
to the ADC’s internal +2.5 V reference.
SPI port data input.
SPI port data output.
Active-low enable output for SPI bus devices.
SPI port clock signal.
7-bit to 12-bit ADC input 2. ADC full scale reading can be referenced to the module’s +3.3 V regulated suppy or
to the ADC’s internal +2.5 V reference.
Module’s +3.3 V regulated suppy, used for ratiometric ADC readings. Current drain on this output should be no
greater than 5 mA.
No connection.
No connection.
RF ground. Connect to the host circuit board ground plane, and to shield when using coaxial cable.
RF port. Connect the antenna to this port with a 50 Ω stripline or semi-rigid coaxial cable.
RF ground. Connect to the host circuit board ground plane, and to shield when using coaxial cable.
4
Description