ZB2430-Q-C-X-U Laird Technologies, ZB2430-Q-C-X-U Datasheet - Page 42
![no-image](/images/manufacturer_photos/0/3/378/laird_technologies_sml.jpg)
ZB2430-Q-C-X-U
Manufacturer Part Number
ZB2430-Q-C-X-U
Description
MOD ANT CONN ZIGBEE 2-100MW U.FL
Manufacturer
Laird Technologies
Series
AeroCommr
Datasheet
1.ZB2430-D-C-S-A-EVB.pdf
(62 pages)
Specifications of ZB2430-Q-C-X-U
Frequency
2.4GHz
Data Rate - Maximum
250kbps
Modulation Or Protocol
802.15.4 Zigbee
Applications
AMR, ISM, Security and Access
Power - Output
10dBm ~ 20dBm
Sensitivity
-99dBm
Voltage - Supply
3 V ~ 3.5 V
Current - Receiving
27mA
Current - Transmitting
25mA
Data Interface
PCB, Through Hole
Antenna Connector
U.FL
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
EEPROM P
The OEM Host can program various parameters that are stored in EEPROM and become active after a power-on
reset. The table below gives the locations and descriptions of the parameters that can be read/written by the OEM
Host. Factory default values are also shown. Do not write to any EEPROM addresses other than those listed below.
Do not copy one transceiver’s EEPROM to another transceiver as doing so may cause the transceiver to malfunction.
End Device Wake Time
End Device Wake Poll
Parent Hold Message
End Device Poll Rate
Channel Number
Channel Mask
Stop Bit Delay
Parameter
Product ID
Rate
EEPROM
Address
0x00
0x30
0x34
0x39
0x3A
0x3C
0x3F
0x40
ARAMETERS
Ta b l e 9 : E E P R O M P a r a m e t e r s
(Bytes)
Length
40
4
2
1
2
2
1
1
www.aerocomm.com
0x0000 - 0xFFFF
0x0000 - 0xFFFF
0x0000 - 0xFFFF
0x00 - 0xFF
0x00 - 0xFF
Range
0x0B -
0x1A
0x07FFF800
Default
0x03E8
0x0064
0x0032
0x0B
0x42
0x00
Description
Product identifier string. Includes revision infor-
mation for software and hardware.
When Channel Select is enabled in EEPROM,
tells the radio the available channels to use in
Channel Select mode.
Specifies how often the End Device will wakeup
from Sleep Mode. and request data from its
parent. 1 ms per increment.
Note: Valid only for End Devices
Specifies the amount of time that a Parent
Device will hold a message for a sleeping End
Device before discarding. 1000 ms per incre-
ment.
Note: Valid only for Coordinator and Routers
Specifies the amount of time that an End
Device will remain awake. 1 ms per increment.
Note: Valid only for End Devices
Specifies how often the End Device should
request messages from its Parent Device while
awake. 1 ms per increment.
Note: Valid only for End Devices
For systems employing the RS-485 interface or
Parity, the serial stop bit might come too early.
Stop bit delay controls the width of the last bit
before the stop bit occurs. Should be set to 2
times the byte time when used.
0x00 = Disable stop bit delay
Note: Stop bit delay only needs to be used
when using external RS485 hardware or RS485
DE/RE.
RF Channel Number. Used when Channel
Select mode is disabled.
8