T5753-6AP Atmel, T5753-6AP Datasheet - Page 9

• Manufacturer Part Number: T5753-6AP
• Description: IC TX 310-330MHZ ASK/FSK 8TSSOP
• Manufacturer: Atmel

Specifications of T5753-6AP

• Frequency: 310MHz ~ 350MHz
• Applications: General Purpose Data Transmission Systems
• Modulation Or Protocol: ASK, FSK
• Data Rate - Maximum: 32 kBaud
• Power - Output: 8dBm
• Current - Transmitting: 9mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 2 V ~ 4 V
• Operating Temperature: -55°C ~ 125°C
• Package / Case: 8-TSSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Memory Size: -
• Other names: T5753-6APTR; T5753-6AQ; T5753-6AQTR; T5753-6AQTR

Figure 4-5.
5. Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
6. Thermal Resistance
7. Electrical Characteristics
V
Typical values are given at V
4510J–RKE–12/08
Parameters
Supply current
Supply current
Supply current
Output power
Note:
Parameters
Supply voltage
Power dissipation
Junction temperature
Storage temperature
Ambient temperature
Input voltage
Note:
Parameters
Junction ambient
S
= 2.0V to 4.0V, T
1. If V
1. If V
ESD Protection Circuit
S
S
is higher than 3.6V, the maximum voltage will be reduced to 3.6V.
+ 0.3 is higher than 3.7V, the maximum voltage will be reduced to 3.7V.
amb
= –40°C to 125°C unless otherwise specified.
GND
VS
S
= 3.0V and T
Test Conditions
Power down,
V
V
V
(100% correlation tested)
Power up, PA off, V
V
Power up, V
V
V
f = 315 MHz, Z
ENABLE
PA-ENABLE
PA-ENABLE
ENABLE
ENABLE
S
= 3.0V, T
amb
< 0.25 V, -40°C to 85°C
> 1.7 V, V
> 1.7 V, V
= 25°C. All parameters are referred to GND (pin 7).
< 0.25 V, -40°C to +125°C
< 0.25 V, 25°C
amb
S
CLK
= 3.0 V,
Load
= 25°C,
V
PA-ENABLE
PA-ENABLE
maxPA_ENABLE
= (255 + j192)W
S
Symbol
Symbol
= 3 V,
T
R
T
PA_ENABLE
P
V
T
amb
thJA
stg
tot
S
j
< 0.25 V
> 1.7 V
ANT1
ANT2
Minimum
–0.3
–55
–55
I
Symbol
S_Transmit
I
P
S_Off
I
Ref
S
Value
XTAL
170
Min.
6.0
(V
Maximum
S
100
150
125
125
+ 0.3)
ENABLE
5
Typ.
< 10
(1)
3.7
8.0
9
Max.
11.6
10.5
350
4.8
7
Unit
mW
Unit
T5753
K/W
°C
°C
°C
V
V
dBm
Unit
mA
mA
nA
µA
nA
9