FCBS0650 Fairchild Semiconductor, FCBS0650 Datasheet
FCBS0650
Specifications of FCBS0650
Available stocks
Related parts for FCBS0650
FCBS0650 Summary of contents
Page 1
... Fairchild Semiconductor Corporation FCBS0650 Rev. A General Description advanced smart power module (SPM) that Fairchild has newly developed and designed to provide very compact and high performance ac motor drives mainly targeting low-power inverter-driven application like refrigerator. It combines opti- mized circuit protection and drive matched to low-loss MOS- FETs ...
Page 2
... V (19) V (19) V B(W) B(W) B(W) B(W) (20) V (20) V (20) V (20) V S(W) S(W) S(W) S(W) FCBS0650 Rev. A Control circuit under-voltage (UV) protection Note) Available bootstrap circuit example is given in Figs. 10 and 11. Top View 13.3 13.3 13.3 19.1 19.1 19.1 Figure 2. 2 (21) N (21) N (21) N ...
Page 3
... FCBS0650 Rev. A Pin Description Low-side Common Bias Voltage for IC and MOSFETs Driving Common Supply Ground Signal Input for Low-side U Phase Signal Input for Low-side V Phase Signal Input for Low-side W Phase Fault Output Capacitor for Fault Output Duration Time Selection Capacitor (Low-pass Filter) for Short-Current Detection Input ...
Page 4
... Inverter low-side is composed of three MOSFETs, and one control IC. It has gate driving and protection functions. 2. Inverter power side is composed of four inverter dc-link input terminals and three inverter output terminals. 3. Inverter high-side is composed of three MOSFETs and three drive ICs for each MOSFET. FCBS0650 Rev. A (19) V B(W) ...
Page 5
... R Junction to Case Thermal th(j-c) Resistance Note: 2. For the measurement point of case temperature(T Package Marking and Ordering Information Device Marking Device FCBS0650 FCBS0650 FCBS0650 Rev 25°C, Unless Otherwise Specified) J Conditions Applied between P- N Applied between 25°C, Peak Sinusoidal Current 25°C, Under 1ms Pulse Width ...
Page 6
... OFF t C(OFF Drain - Source DSS Leakage Current Note and t include the propagation delay time of the internal drive IC OFF For the detailed information, please see Figure 100 90 10 (a) Turn-on FCBS0650 Rev 25°C, Unless Otherwise Specified) J Conditions 15V I =3A 15V I =3A 300V 15V PN ...
Page 7
... Control Supply Voltage CC V High-side Bias Voltage BS dV /dt, Control supply variation Blanking Time for Preventing dead Arm-short f PWM Input Signal PWM V Voltage for Current Sensing SEN FCBS0650 Rev 25°C, Unless Otherwise Specified) J Conditions V = 15V V - COM CC CC( (UL, VL, WL 15V CC(UH) CC(VH) ...
Page 8
... Mechanical Characteristics and Ratings Parameter Mounting Torque Mounting Screw Device Flatness Weight FCBS0650 Rev. A Conditions Recommended 0.62N•m Note Fig Figure 5. Flatness Measurement Position 8 Limits Units Min. Typ. Max. 0.51 0.62 0.72 N•m µ +120 - 15 www.fairchildsemi.com ...
Page 9
... Normal operation: MOSFET ON and carrying current Under voltage detection (UV BSD b4 : MOSFET OFF in spite of control input condition, but there is no fault output signal Under voltage reset (UV ) BSR b6 : Normal operation: MOSFET ON and carrying current Figure 7. Under-Voltage Protection (High-side) FCBS0650 Rev. A RESET SET UV CCR a1 UV CCD a3 ...
Page 10
... Fault output timer operation starts: The pulse width of the fault output signal is set by the external capacitor Input “L” : MOSFET OFF state Input “H”: MOSFET ON state, but during the active period of fault output the MOSFET doesn’t turn ON MOSFET OFF state Figure 8. Short-Circuit Current Protection (Low-side Operation only) FCBS0650 Rev SET RESET ...
Page 11
... It would be recommended that the bootstrap diode The bootstrap resistor (R ) should be 3 times greater than high-side. 3. The ceramic capacitor placed between V -COM should be over 1uF and mounted as close to the pins of the SPM as possible. CC Fig. 10. Recommended Bootstrap Operation Circuit and Parameters FCBS0650 Rev. A 5V-Line Ω 4.7k Ω 100 ...
Page 12
... P&COM pins is recommended. 11. Relays are used at almost every systems of electrical equipments of home appliances. In these cases, there should be sufficient distance between the CPU and the relays. 12. C should be over 1µF and mounted as close to the pins of the SPM as possible. SPC15 FCBS0650 Rev. A 15V line ...
Page 13
... Detailed Package Outline Drawings FCBS0650 Rev www.fairchildsemi.com ...
Page 14
... Detailed Package Outline Drawings FCBS0650 Rev. A (Continued) 14 www.fairchildsemi.com ...
Page 15
... Detailed Package Outline Drawings FCBS0650 Rev. A (Continued) 15 www.fairchildsemi.com ...
Page 16
... TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended exhaustive list of all such trademarks. FAST ® ACEx™ ActiveArray™ FASTr™ Bottomless™ FPS™ Build it Now™ FRFET™ CoolFET™ ...