PSE530-M5 SMC Corporation of America, PSE530-M5 Datasheet
![no-image](/images/no-image-200.jpg)
PSE530-M5
Specifications of PSE530-M5
Related parts for PSE530-M5
PSE530-M5 Summary of contents
Page 1
... Sensor cable ZS-26-F Cable length Cable length Connector + ZS-26-G The connector is not connected to Sensor cable the cable at the time of shipment. Specifications PSE530-M5 Model Rated pressure range MPa Proof pressure 1.5 MPa Fluid Power supply voltage Current consumption Output specification Accuracy ...
Page 2
... DC (+) Power supply Brown DC (–) GND Analog output ( Dimensions PSE53-M5 3.4 With sensor cable Pressure Sensor Brown Black Blue Blue Black 29.4 0.5 27 5.5 PSE530 Series VDC Load M5 x 0.8 Pressure port 12 ZSE ISE PSE Z SE3 ZSP ISA2 IS ...
Page 3
... Incorrect wiring can damage the switch and cause a malfunction or erroneous switch output. Connections should be done while the power is turned off not attempt to insert or pull the pressure sensor or its connector when the power is on. Switch output may malfunction. 3. Wire separately from power lines and high voltage lines, avoiding wiring in the same conduit with these lines ...
Page 4
... Use a new sensor connector in case wiring or the snapping of A into B are done incorrectly • To connect the connector to the multi-channel pressure sensor, push the connector with its A portion facing toward you into the socket until it clicks as shown below. • To remove the connector, pull it straight out while applying pressure to the fingers on both sides ...
Page 5
... SMC pressure sensors, Series PSE510 & PSE520, are also connectable. • When connecting to pressure sensors other than the Series PSE530, connector types will vary depending on the wire core size of the cable and the outside diameter of the insulation cover. Refer to the table provided below. ...
Page 6
... When equipment removed, confirm the safety process as mentioned above. Cut the supply pressure for this equipment and exhaust all residual compressed air in the system. 3. Before machinery/equipment is restarted, take measures to prevent shooting-out of cylinder piston rod, etc ...
Page 7
... Remove drainage from air filters regularly. (Refer to the specifications.) 4. Shut-down before maintenance Before attempting any kind of maintenance make sure the supply pressure is shut of and all residual air pressure is released from the system to be worked on. 5. Start-up after maintenance and inspection Apply operating pressure and power to the equipment and check for proper operation and possible air leaks ...
Page 8
Quality Assurance Information (ISO 9001, ISO 14001) Reliable quality of products in the global market To enable our customers throughout the world to use our products with even greater confidence, SMC has obtained certification for international standards “ISO 9001” and ...
Page 9
... This directive is applied to products, which operate above 50 VAC to 1000 VAC and 75 VDC to 1500 VDC operating voltage, and require electrical safety measures to be introduced. • Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 16-14-6 ...
Page 10
... CSA and UL Standards. í TSSA (MCCR) Registration Products TSSA is the regulation in Ontario State, Canada. The products that the operating pressure is more than 5 psi (0.03 MPa) and the piping size is bigger than 1 inch. fall into the scope of TSSA regulation. Products conforming to CE Standard ...
Page 11
... SMC’s Global Service Network America U.S.A. SMC Corporation of America 3011 North Franklin Road Indianapolis, IN 46226, U.S.A. TEL: 317-899-4440 FAX: 317-899-3102 CANADA SMC Pneumatics (Canada) Ltd. 6768 Financial Drive Mississauga, Ontario, L5N 7J6 Canada TEL: 905-812-0400 FAX: 905-812-8686 MEXICO SMC Corporation (Mexico), S.A. DE C.V. ...
Page 12
Europe FINLAND SMC Pneumatics Finland OY PL72, Tiistinniityntie 4, SF-02231 ESP00, Finland TEL: 09-8595-80 FAX: 09-8595-8595 NORWAY SMC Pneumatics Norway A/S Vollsveien 13C, Granfoss Næringspark N-1366 LYSAKER, Norway TEL: 67-12-90-20 FAX: 67-12-90-21 BELGIUM (Distributor) SMC Pneumatics N.V./S.A. Nijverheidsstraat 20 B-2160 ...