PSE531-M5 SMC Corporation of America, PSE531-M5 Datasheet - Page 3

• Manufacturer Part Number: PSE531-M5
• Description: SENSOR VACUUM 101KPA M5 PORT
• Manufacturer: SMC Corporation of America
• Series: PSE530r

Specifications of PSE531-M5

• Pressure Type: Vacuum
• Operating Pressure: -14.65 ~ +0 PSI, -101 ~ 0 kPa
• Port Size: Female, 0.8" (20.32mm) NPT
• Output: Digital
• Voltage - Supply: 12 V ~ 24 V
• Termination Style: Cable with Connector
• Package / Case: Cylinder, Metal
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 606-1020

{ Pressure Sensor
1. The pressure sensors are CE marked; however, they
2. The pressure sensors do not have an explosion
1. Do not drop, bump, or apply excessive impacts (980
3. Do not exceed the screw-in torque of 3.5 N⋅m when
4. Do not use pressure sensors with corrosive and/or
5. Connecting the sensor cable (Option)
2. The tensile strength of the cord is 23 N. Applying a
A connector cover is provided as part of the cable assembly
(see the figure below). It is designed to keep the female
connector from slipping out of the sensor. To lock the connector
cover in place, first make sure it is facing in the right direction
as you slip it over the female connector, then lock it to the
sensor body by turning it clockwise. To remove the cover, first
unlock it by turning it counterclockwise, then pull back on it. To
remove the female connector, grab it with your fingers and pull
back on it. Do not pull on the cable.
are not equipped with surge protection against
lightning. Lightning surge countermeasures should
be applied directly to system components as
necessary.
proof rating. Never use pressure sensors in the
presence of inflammable or explosive gases.
m/s
sensor may not be damaged, the inside of the
sensor
malfunction.
greater pulling force on it can cause a malfunction.
When handling, hold the body of the sensor—do
not dangle it from the cord.
installing piping. Exceeding this value may cause
malfunctioning of the sensor.
inflammable gases or liquids.
Hold the female connector of the sensor cable with your
fingers and carefully insert it into the connector.
Warning
Warning
2
) while handling. Although the body of the
could
Operating Environment
Lock
Series
Specific Product Precautions 1
Be sure to read before handling.
be
Handling
damaged
Unlock
Female connector
PSE
Connector cover
Male connector
Sensor
Sensor
and
lead
to
a
1. Do not drop, bump, or apply excessive impacts
2. The tensile strength of the power supply/output
1. Our multi-channel pressure sensor controllers are
2. Our multi-channel pressure sensor controllers do
3. Enclosure “IP65” applies only to the front face of
{ Controller
1. Incorrect wiring can damage the switch and cause
2. Do not attempt to insert or pull the pressure sensor
3. Wire separately from power lines and high voltage
4. If a commercial switching regulator is used, make
(1000 m/s
the controller case may not be damaged, the inside
of the controller could be damaged and cause a
malfunction.
connection cable is 50 N; that of the pressure
sensor lead wire with connector is 25 N. Applying a
greater pulling force than the applicable specified
tensile strength to either of these components can
lead to a malfunction. When handling, hold the
body of the controller—do not dangle it from the
cord.
CE marked; however, they are not equipped with
surge protection against lightning. Lightning surge
countermeasures should be applied directly to
system components as necessary.
not have an explosion proof rating. Never use
pressure sensors in the presence of inflammable or
explosive gases.
the panel when mounting. Do not use in an
environment where oil splashing or spraying are
anticipated.
a malfunction or erroneous switch output.
Connections should be done while the power is
turned off.
or its connector when the power is on. Switch
output may malfunction.
lines, avoiding wiring in the same conduit with
these lines. Malfunctions may occur due to noise
from these other lines.
sure that the F.G. terminal is grounded.
Warning
Warning
Warning
2
) while handling. Although the body of
Operating Environment
Connection
Handling
16-3-19
ZSE„
ISE„
PSE
Z
PS
Z
ZSP
ISA2
IS„
ZSM
PF2„
IF„
Data
I
I
SE3
SE
1
2