35941 Desco, 35941 Datasheet - Page 2

• Manufacturer Part Number: 35941
• Description: ARM ADJUSTABLE FOR THE EXTRACTOR
• Manufacturer: Desco
• Series: Menda®r

Specifications of 35941

• Accessory Type: Swing Arm
• For Use With/related Products: 35940
• Lead Free Status / RoHS Status: Contains lead / Not applicable

TB-4001 Page 2 of 2
The Swing Arm’s custom neckpiece allows for easy
mounting of a standard The Extractor via the installed
stand assembly. The Extractor should be mounted to
the stand and neckpiece as shown in Figure 4.
Figure 4: Installing The Extractor to Swing Arm
Operation
Plug the unit into a properly grounded electrical outlet.
Place the front grill side of the unit as close to the smoke
source as possible, without interfering with the user’s
operation. Make sure the exhaust side of the unit is free
from obstruction and away from the user’s face. Turn
the lighted rocker switch to the on position. The
Extractor is now ready to extract smoke and particulate
away from the operator. A standard banana jack
receptacle is located on the front of the unit to allow for
grounding of a wrist strap and cord assembly for ESD
control purposes. For safety reasons, only ground cords
with resistors of the proper value should be used with
The Extractor.
User Maintenance
The replaceable foam filter on the intake side of The
Extractor is the only user serviceable part. To replace
the filter, place the lighted rocker switch to the off
position and unplug the unit from the building’s electrical
outlet. Simply unsnap the plastic holder from the unit,
dispose of the soiled filter, replace with a new filter
(35942), and remount the plastic holder. The longevity
of the filter will vary depending on how often The
Extractor is used and how clean the environment is that
it is placed in. A good rule of thumb is, “When it looks
dirty, it’s time to replace it.” If the unit needs further
maintenance, contact Menda’s customer service
department for an RMA.
Figure 5: Replace the filter.
Air Filter
Phone: [phone] • Fax [phone] • Web Site: MendaPump.com
3651 Walnut Avenue, Chino, CA 91710
Specifications
Input:
Fuse Type:
Cord:
Airflow:
Weight:
Dimensions:
Adjustment and Calibration
None needed.
Limited Warranty
Menda expressly warrants that for a period of one (1) year from the
date of purchase, Menda Extractors will be free of defects in
material (parts) and workmanship (labor). Within the warranty
period, the product will be tested, repaired, or replaced at Menda’s
option, free of charge. Call our Customer Service Department at
909-627-2453 for a Return Material Authorization (RMA) and
proper shipping instructions and address. Include a copy of your
original packing slip, invoice, or other proof of purchase date. Any
unit under warranty should be shipped prepaid to the Menda
factory. Warranty repairs will take approximately two weeks.
If your unit is out of warranty, call Customer Service at 909-627-
2453 for a Return Material Authorization (RMA) and proper
shipping instructions and address. Menda will quote repair
charges necessary to bring your unit up to factory standards.
Warranty Exclusions
THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OF
ALL OTHER PRODUCT WARRANTIES, EXPRESSED AND
IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE WHICH ARE SPECIFICALLY
DISCLAIMED. The express warranty will not apply to defects or
damage due to accidents, neglect, misuse, alterations, operator
error, or failure to properly maintain, clean or repair products.
Limit of Liability
In no event will Menda or any seller be responsible or liable for any
injury, loss or damage, direct or consequential, arising out of the use
of or the inability to use the product. Before using, users shall
determine the suitability of the product for their intended use, and
users assume all risk and liability whatsoever in connection
therewith.
34940
35943
35940
35941
35943
35940, 35943
35941
35940, 35943
35940, 35943
35941
35941
120 VAC - 50-60 Hz, 200mA
220 VAC - 50-60 Hz, 120mA
Fast Blow 1 amp
7'6" IEC cord set
Internal
No cord supplied
3.0 pounds
2.0 pounds
without stand - 6.7" x 6.6" x 3.5"
with stand - 8.5" x 7.75"
Base: 6.8" x 3.4"
Holes: 0.122" in diameter, in a
5.83" x 2.4" rectangular pattern
40" usable reach
Diameter of the stem: 1/2"
80 CFM
© 2006 DESCO INDUSTRIES INC.
Employee Owned