60-BGA-5 ITW Chemtronics, 60-BGA-5 Datasheet
60-BGA-5
Manufacturer Part Number
60-BGA-5
Description
SOLDER-WICK BGA NO-CLEAN 5'
Manufacturer
ITW Chemtronics
Series
Soder-Wick® SW 60r
Type
No Cleanr
Specifications of 60-BGA-5
Length
5' (1.52m)
Color
Purple
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
ITW CHEMTRONICS
SECTION 1: CHEMICAL PRODUCT AND COMPANY INFORMATION
Company Address:
8125 Cobb Center Drive
Kennesaw, GA 30152
Product Identification
Product Code: 60 Series (All part numbers)
SECTION 2: COMPOSITION, INFORMATION ON INGREDIENTS
Product Ingredient Information
Copper
Rosin
SECTION 3: HAZARD IDENTIFICATION
Emergency Overview: Shiny, braided copper wire. This product is nonflammable.
Potential Health Effects:
Eyes: Vapors released from the desoldering process may cause eye irritation.
Skin: Prolonged contact may cause skin irritation and/or sensitization.
Ingestion: Not likely.
Inhalation: Vapors from soldering processes may cause irritation of the nose and throat. Respiratory sensitization may result from inhalation of rosin fumes.
Pre-Existing Medical Conditions Aggravated by Exposure: Lung and skin.
SECTION 4: FIRST AID MEASURES
Eyes:
Have eyes examined and tested by medical personnel if irritation develops or persists.
Skin:
clothing separately before reuse.
Ingestion: Get medical attention.
Inhalation: If user is overcome by fumes during the desoldering process remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen and get iimmediate medical attention.
SECTION 5: FIRE FIGHTING MEASURES
Flash Point: Nonflammable
Extinguishing Media: Water fog, CO 2 , dry chemical, foam are compatible for extinguishing fires involving other materials when Soder-Wick is present.
Fire Fighting Instructions: As in any fire, wear self-contained breathing apparatus (pressure-demand, MSHA/NIOSH approved or equivalent) and full protective gear.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Small Spills: Pick up and store in a closed container for delivery to a metals recycling center. Do not dispose of by placing in trash.
SECTION 7: HANDLING AND STORAGE
Avoid prolonged or repeated contact with eyes and skin. Wash hands before eating. Use with adequate ventilation. Avoid breathing vapors given off by he
desoldering process. Store in a cool dry place. Keep container closed when not in use. KEEP OUT OF REACH OF CHILDREN.
SECTION 8: EXPOSURE CONTROLS/PERSONNEL PROTECTION
Exposure Guidelines:
CHEMICAL NAME
Copper
Rosin
NFPA and HMIS Codes:
Health
Flammability
Reactivity
Personal Protection
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Coated braided copper wire
Odor: Mild
pH: NA
Vapor Pressure: NA
Vapor Density: NA
Color: Copper metallic
Work/Hygienic Practices: Local exhaust ventilation is recommended. Wear safety glasses with side shields or goggles when using this product.
If eye irritation occurs immediately flush with plenty of water. After initial flushing, remove any contact lenses and continue flushing for at least 15 minutes.
If skin irritation occurs wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation develops or persist. Wash
Product Information: 800-TECH-401
Customer Service:
®
800-645-5244
SODER-WICK® NO CLEAN SD
LEL/UEL: Not applicable
ACGIH TLV
0.2 g/m
NA
m
Page 1 of 2
CAS#
NFPA
7440-50-8
8050-09-7
1
0
1
-
3
Emergency:
Revision Date: February 17, 2010
Solubility in Water: Insoluble
Specific Gravity: (Water =1) 8.92
Evaporation Rate: NA
Viscosity: NA
Percent Volatile: NA
Boiling Point: 604F @ 100mm Hg
OSHA PEL
1.0 g/m
NA
(Chemtrec) 800-424-9300
m
3
Wt. % Range
90.0-98.0
HMIS
2.0-10.0
1
0
1
-
ACGIH STEL
NA
NA
MSDS #1402
60-BGA-5 Summary of contents
Page 1
... Cobb Center Drive Kennesaw, GA 30152 Product Information: 800-TECH-401 Customer Service: 800-645-5244 Product Identification Product Code: 60 Series (All part numbers) SECTION 2: COMPOSITION, INFORMATION ON INGREDIENTS Product Ingredient Information Copper Rosin SECTION 3: HAZARD IDENTIFICATION Emergency Overview: Shiny, braided copper wire. This product is nonflammable. ...
Page 2
... ITW CHEMTRONICS SECTION 10: STABILITY AND REACTIVITY Stability - This product is stable. Conditions to Avoid: None known Incompatibility: Do not mix with powdered alkali and alkaline earth metals or strong oxidizing agents. Products of Decomposition: Carbon dioxide, carbon monoxide. Hazardous Polymerization: Will not occur Conditions to Avoid: NA SECTION 11: TOXICOLOGICAL INFORMATION Inhalation: Inhalation of dust and fumes during desoldering can irritate the respiratory tract and cause respiratory sensitization ...