537202000 C&K Components, 537202000 Datasheet - Page 5

• Manufacturer Part Number: 537202000
• Description: HDWR ADHESIVE MYLAR WASHER M SRS
• Manufacturer: C&K Components
• Type: Washerr
• Series: 537r

Specifications of 537202000

• Accessory Type: Adhesive Mylar Washer
• Switch Type: Rotary Switch
• Operating Temp Range: -30C to 85C
• Color: Natural
• Termination Style: Adhesive
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: M Series
• For Use With: MB00L1NCQD - SW ROTARY DP 5POS 6A THRU SILVCKN10043 - SWITCH ROTARY DP 5POS 6A SLD MNTMA03L1NZQD - SWITCH ROTARY SP-3POSMC12L1NZGD - SWITCH ROTORY SP 12 POS SOLDER LMA04L2NZGF - ROTARY SWITCH SP 4POSCKN6046 - SWITCH ROTARY DP 5POS 6A SLD MNTCKN6045 - SWITCH ROTARY SP 10POS 6A SLD MTCKN6044 - SWITCH ROTARY SP 10POS 6A PCBCKC7012 - SWITCH ROTARY DP 6POS PC MNTCKC7011 - SWITCH ROTARY SP 12POS PC MNTCKC7010 - SWITCH ROTARY 2P 6POS EYELETCKC7009 - SWITCH ROTARY SP 12POS EYELETMB05L1NCQD - SWITCH ROTARY DP PC MNT 5POSMD06-L1-N-Z-Q-D - SWITCH ROTARY 2P 6POS SLDR LUG
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: *537202000; CKN9418

M Series
Half-inch Rotary Switches
SEAL
D
F
NO EPOXY SEAL
SPLASHPROOF SHAFT AND PANEL SEAL
IP67 approved
Setting Stops With Stop Pins
MA00, MB00, MC00 & MD00 Models Only:
The number of switch positions or stops are adjustable by means of stop pins provided with each switch. Switches are normally
shipped with stop pins and hardware in bulk, not installed. Without stop pins, switches have full 360º rotation and no stops.
Note that all two pole models begin to repeat when actuated 180º or more.
To set stops, refer to figures 1 & 2. Orient switch so that terminal no. 1 is as shown. Turn actuator to position 1, using flats on
bushing and terminal no. 1 as reference. Install CCW stop pin in hole designated ‘X’. Install second stop pin in hole number
corresponding to the number of positions desired. Note that two pole models will begin to repeat when actuated 180º or more.
To retain stop pins, use adhesive mylar washer included; see figure 3.
All models except MX00 models have number of switch positions or stops pre-set at factory and are not adjustable.
Hardware:
Two stop pins, mounting nut, and lockwasher supplied standard.
P/N 537100000
K
36º Indexing Models
30º Indexing Models
Top View
Top View
P/N 537202000
Fig. 1
Fig. 2
Fig. 3
Setting Stops With Stop Rings
ME00, MF00, MG00 & MH00 Models Only:
The number of switch positions or stops are adjustable by means of stop rings provided with each switch. These models are
normally shipped with stop rings and hardware in bulk, not installed. Without stop rings, switches have full 360º rotation and no
stops. Note that all two pole models begin to repeat when actuated 180º or more.
To set stops refer to figures 4 & 5. Orient switch so that terminal no. 1 is as shown. Turn actuator to pos. 1 using flats on bushing
and terminal no. 1 as reference. See figure 6 and install inner stop ring with short tab in hole designated ‘X’. Install outer
stop ring with long tab in hole number corresponding to the number of positions desired. Note that all two pole models begin to
repeat when actuated 180º or more. Use mounting nut and lockwasher to retain stop rings.
All MEXX, MFXX, MGXX & MHXX Models (Except MX00 models):
Number of switch positions or stops are preset at factory, but are user adjustable.
Hardware:
Two stop rings, mounting nut and lockwasher supplied standard.
36º Indexing Models
30º Indexing Models
Top View
Top View
Fig. 4
Fig. 5
Fig. 6
Dimensions are shown: mm
Specifications and dimensions subject to change
www.ck-components.com
K–17