D4DS-K3 Omron, D4DS-K3 Datasheet

Page 1

... CSA C22.2 No.14 BIA GS-ET-15, EN60947-5-1 SUVA SUVA Note: CSA C22.2 No. 14 compliance was verified and approved by UL (Marked with Conformity: Machine Directive Low-voltage Directive prEN1088 and double File No. R9551708 E76675 1-conduit: 9509915 2-conduit: 9509913 1-conduit: Nr.6010Z 2-conduit: Nr.6011Z D4DS 1 ...

Page 2

... Pg13.5 G1/2 Accessories (Order Separately) Operation Key Mounting type Horizontal D4DS-K1 Vertical D4DS-K2 Adjustable D4DS-K3 (horizontal Head Mounting Direction F: Front-side mounting 4. Head Variation S: Standard Note: Note that any order for the head part or the switch part alone cannot be accepted. The Operation Key is sold separately. ...

Page 3

... Motor load has an inrush current of 6 times the steady-state current. Current Make Break 1 1.2 A Lamp load Inductive load 1 1 0.2 A 0.2 A 0.8 A 0.1 A 0.1 A 0.4 A D4DS Voltage Ampere Make Break 7,200 VA 720 VA Inductive load Motor load 2 1.5 A 1 0 ...

Page 4

... Release force (insertion) Pretravel Total travel (reference value) Min. positive opening force (see note) Min. positive opening stroke (see note) Note: Make sure that the positive opening stroke is at least order to use the D4DS safely. 4 0.1 m/s to 0.5 m min. 30 operations/min 100 M min. (at 500 VDC) between terminals of same polarity, between terminals of ...

Page 5

... The cover, with a hinge on its lower part, can be opened by removing the screw of the cover, which ensures ease of maintenance and wiring. Note: The housing and head of the D4DS are made of synthetic resin. If high mechanical durability is required, use the D4BS Safety Door Switch. D4DS Head The head can be mounted in four directions ...

Page 6

... D4DS Operation Contact Form Model Contact D4DS 1NC/1NO 11 23 D4DS 2NC 11 21 Note: Terminals are numbered according to EN50013 and contacts are marked according to EN60947-5-1. Positive Opening Mechanism 1NC/1NO Contact (Slow-action) Contact spring Return spring Only the NC contacts have a positive open- ing function. ...

Page 7

... S/-5 S D4DS-2 S/-6 S D4DS R2.15 0.05 mounting holes See note 3 on page R2.15 0.05 mounting holes See note 3 56 max. on page 7. D4DS-K2 D4DS-K3 Four, R2.15 D4DS +0.15 Two, 4 dia. holes 0 depth: 5 Cap +0.15 Two, 4 dia. holes 0 depth dia. 4.5 dia. 8 dia. 7 ...

Page 8

... Operation Key and key hole. D4DS D4DS-K3 D4DS D4DS-K3 D4DS D4DS-K3 D4DS D4DS-K3 D4DS D4DS-K3 Horizontal key 44 to 46.5 insertion radius Key insertion face R Permissible difference in center lines between the Operation Key and key hole 46.5 Key insertion face ...

Page 9

... To prevent the D4DS from damage due to short-circuits, connect the D4DS in series to a fuse that has a breaking current 1 times the rated current of the D4DS. If the D4DS is used under EN-ap- proved rating conditions, use fuse type conforming to IEC 269 ...

Page 10

... Operation Key Mounting Holes Horizontal/Vertical Mounting (D4DS-K1/-K2) Adjustable Mounting (D4DS-K3) Head Direction By removing the four screws of the head, the mounting direction of the head can be changed. The head can be mounted in four direc- tions. When changing the direction of the head, be sure that the Operation Key is inserted into the head and no foreign material will enter during a change in direction ...

Page 11

... Be sure that no metal dust, oil, or chemical will be sprayed onto the D4DS, otherwise the D4DS may malfunction. The head uses grease internally, which may have a bad influence on semiconductor products. When using the D4DS for the door of a semiconductor product manufacturing room, mount the D4DS to the outer side of the door. ...

Page 12

... To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. C104-E1-2 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Control Components Division H.Q. 28th Fl., Crystal Tower Bldg. 1-2-27, Shiromi, Chuo-ku, Osaka 540 Japan Phone: 06-949-6115 Fax: 06-949-6134 12 D4DS Printed in Japan 0897-1M (0696) a ...