FR01FR10P-S NKK Switches, FR01FR10P-S Datasheet - Page 3

• Manufacturer Part Number: FR01FR10P-S
• Description: SW ROTARY DIP DEC RED STRAIGHT
• Manufacturer: NKK Switches
• Series: FR01r
• Type: Rotary, DIPr

Specifications of FR01FR10P-S

• Circuit: BCD
• Number Of Positions: 10
• Contact Rating @ Voltage: 0.1A @ 5VDC
• Actuator Type: Rotary for Tool
• Actuator Level: Flush
• Mounting Type: Through Hole
• Orientation: Top Actuated
• Washable: No
• Output Code: Real
• Actuator: Screwdriver
• Contact Rating: 100 mAmps at 5 Volts
• Termination Style: Straight PC
• Dielectric Strength: 250 Volts
• Current, Rating: 100 mA
• Mounting Hole Size: 0.031-0.039 "
• Special Features: Programmable Legend
• Termination: Through Hole
• Voltage, Rating: 5 VDC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 360-2198

General Specifications
Electrical Capacity (Resistive Load)
Other Ratings
Materials & Finishes
Environmental Data
PCB Processing
Standards & Certifications
NKK Switche
Operating Temperature Range:
Nominal Operating Torque:
Flammability Standards:
Nonswitching Rating:
Insulation Resistance:
Stationary Contacts:
or CSA Certification:
Contact Resistance:
Dielectric Strength:
Movable Contacts:
Switching Rating:
Housing & Base:
Mechanical Life:
Terminal Cover:
Contact Timing:
UL Recognition
Electrical Life:
Outer Case:
Soldering:
Actuators:
Terminals:
Vibration:
Humidity:
Cleaning:
Bushing :
Bracket:
Shock:
100mA @ 5V DC
100mA @ 50V DC
100 milliohms maximum for circuit; 30 milliohms maximum for contact point
1,000 megohms minimum @ 250V DC
250V AC minimum for 1 minute minimum
10,000 detent operations minimum
10,000 detent operations minimum
Notes: A detent operation is one actuator position operation or stepping.
Metal Shaft: 0.009Nm for decimal devices; 0.011Nm for hexadecimal devices
All other Actuator types: 0.008Nm for decimal devices; 0.01Nm for hexadecimal devices
Shorting (Avoid possible false signal by turning off power before switching.)
Screwdriver and Plastic Shaft - Glass fiber reinforced polyamide (UL94V-0);
Dial - Polyoxymethylene; Metal Shaft - Brass with nickel plating
Brass with nickel plating (for Metal Shaft model)
Glass fiber reinforced PBT (for Metal Shaft model)
Glass fiber reinforced polyamide (UL94V-0)
Copper alloy with gold plating
Phosphor bronze with gold plating
Phosphor bronze with gold plating
Polyamide (Right angle model only)
Phospher bronze with tin plating (for Metal Shaft model)
–25°C through +85°C (–13°F through +185°F)
90 ~ 95% humidity for 240 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 5 minutes; 3 right angled directions for 2 hours
50G (490m/s
Wave Soldering Recommended. See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
These devices are not process sealed. Hand clean locally using alcohol based solution.
UL94V-0 rated actuator, housing and base
The FR01 Series rotaries have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current circuit.
When used as intended, the results do not produce hazardous energy.
A cycle is one 360° rotation. 10,000 detent operations equal 625
cycles for hexadecimal devices or 1,000 cycles for decimal devices.
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
10mm DIP Rotaries
Series FR01