DRAR16H NKK Switches, DRAR16H Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/4/479/nkk_switches_sml.jpg)
DRAR16H
Manufacturer Part Number
DRAR16H
Description
SW ROTARY DIP HEX ORN RT ANGLE
Manufacturer
NKK Switches
Series
DRr
Datasheet
1.DRAR16H.pdf
(6 pages)
Specifications of DRAR16H
Circuit
Hexadecimal
Number Of Positions
16
Contact Rating @ Voltage
0.1A @ 5VDC
Actuator Type
Rotary with Shaft
Actuator Level
Raised
Mounting Type
Through Hole
Orientation
Side Actuated
Washable
Yes
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
General Specifications
NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435
Electrical Capacity (Resistive Load)
Other Ratings
Materials & Finishes
Environmental Data
Installation
Standards & Certifications
Soldering Time & Temperature:
Shaft & Bushing (DRA only):
Nominal Operating Torque:
Mounting Torque for DRA:
Flammability Standards:
Operating Temp Range:
Knob Installation Force:
Nonswitching Rating:
Insulation Resistance:
or CSA Certification:
Stationary Contacts:
Contact Resistance:
Dielectric Strength:
Movable Contact:
Switching Rating:
Housing & Case:
Mechanical Life:
Contact Timing:
UL Recognition
Electrical Life:
Process Seal:
Terminals:
Vibration:
Humidity:
Actuator:
O-rings:
Note: A detent operation is one actuator position operation or stepping.
Shock:
20,000 detent operations = 1,250 cycles for hexadecimal devices or
Base:
2,000 cycles for decimal devices. A cycle is one 360° rotation.
100mA @ 5V DC
100mA @ 50V DC
80 milliohms maximum for all 4 contacts closed
30 milliohms maximum for 1 contact closed
1,000 megohms minimum @ 250V DC
250V AC minimum for 1 minute minimum
20,000 detent operations minimum
20,000 detent operations minimum
80 ~ 320 grams-cm (1.1 ~ 4.4 ounce
Shorting (Avoid possible false signal by turning off power before switching.)
Brass with nickel plating
Glass fiber reinforced polyester (PBT) (UL 94V-0)
Glass fiber reinforced polyester (PBT) (UL 94V-0)
Nitrile butadiene rubber
Glass fiber reinforced polyester (PBT) (UL 94V-0)
Copper with gold plating
Phosphor bronze with gold plating
Phosphor bronze with gold plating
-25°C through +75°C (-13°F through +167°F)
90 ~ 95% for 96 hours @ 40C° (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
1.47Nm (13.0 lb
39.2N maximum (8.82 lbf) for DRA model; 29.4N maximum (6.61 lbf) for DRF/DRF2 models
3 seconds @ 350°C manual soldering or 5 seconds @ 270°C solder pot
See Supplement Index (page Z2) for specific processing data.
UL 94V-0 rated actuator, housing, case, & base
The DR series rotaries have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
2
10mm Washable DIP Rotaries
) acceleration (tested in 3 right angled directions, with 3 shocks in each direction)
•
in) for double nut; .686Nm (6.08 lb
•
in)
•
www.nkkswitches.com
in) for single nut
Series DR
8-03