A22-MR-01M Omron, A22-MR-01M Datasheet - Page 26
![SWITCH PB MUSH MOM SPST-NC RED](/photos/14/92/149286/a22-mr-01m_sml.jpg)
A22-MR-01M
Manufacturer Part Number
A22-MR-01M
Description
SWITCH PB MUSH MOM SPST-NC RED
Manufacturer
Omron
Series
A22r
Type
Standardr
Specifications of A22-MR-01M
Circuit
SPST-NC
Switch Function
On-Mom
Contact Rating @ Voltage
10A @ 110VAC
Actuator Type
Mushroom Button
Mounting Type
Panel Mount
Termination Style
Screw Terminal
Contact Form
SPST - NC
Contact Rating
10 mAmps
Actuator
Round, Mushroom
Mounting Style
Panel
Illumination
Illuminated
Illumination Color
Red
Body Shape
Square
Dielectric Strength
2500 Volts
Insulation Resistance
100 MOhms
Mounting Angle
Straight
Operating Force
29.4 N
Water / Moisture Rating
IP65
Ip Rating
IP65
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Illumination Type, Color
-
Illumination Voltage (nominal)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
A22MR01M
Z1460
Z1460
Installation
Common to A22, A22S/W, A22K, M22, and A22E
■ Mounting to the Panel
Panel Hole Dimensions
For 25-dia. holes, always use 25-dia. Rings. (Since the cutout dimen-
sions are large, IP65 cannot be guaranteed unless 25-dia. Rings are
used.)
If outer surface treatment such as coating is performed for the panel,
the panel dimensions after outer surface treatment must meet the
specified panel dimensions.
Note: Recommended panel thickness: 1 to 5 mm.
Matrix Installation
1. The following panel hole dimensions apply when Switch Unit and
G-100
the Standard-size Legend Plate Frame and Lock Ring are
mounted, and lead wires are connected directly to the Switch
Block.
Pushbutton Switch
22 dia.
A22
A
25 dia.
2. The following panel hole dimensions apply when the Large-size
Pitches A and B between the centers of the mounting holes are as
follows:
For 1. above:
For 2. above:
Note: 1. The above dimensions are the minimum dimensions for
A22-10, A22-10S, A22-01, A22-01S
A22-20, A22-20S, A22-02, A22-02S, A22-11,
A22-11S
Bare crimp termi-
nals
Crimp terminals
with insulating
sheath
Legend Plate Frame is mounted, and when crimp terminals are
connected to the Switch Block terminals.
Type of crimp
terminal
2. With pushbuttons of external dimensions greater than
3. When using a pushbutton with external dimensions exceed-
when the wires described under Applicable Wire Size on
page 106 are used. If a different wires are used, the wiring
dimensions may be different so determine an appropriate
pitch before setup.
30 mm, set the pitch according to the dimensions. (When
using matrix installation for the A22-M@, mount with a pitch
of 40 mm instead of 30 mm in the diagram above.)
ing 30 mm, use a pitch appropriate for the pushbutton.
Switch Blocks
A22-10, A22-10S, A22-01,
A22-01S
A22-20, A22-20S, A22-02,
A22-02S, A22-11, A22-11S
A22-10, A22-10S, A22-01,
A22-01S
A22-20, A22-20S, A22-02,
A22-02S, A22-11, A22-11S
Switch Blocks
B
45 mm min.
55 mm min.
51 mm min.
61 mm min.
60 mm min.
70 mm min.
A
B