JF15AP1FF NKK Switches, JF15AP1FF Datasheet

JF15AP1FF

Manufacturer Part Number

JF15AP1FF

Description

SWITCH TACT LP ILLUM SPST GRN

Manufacturer

NKK Switches

Series

JFr

Type

Illuminatedr

Datasheet

1.JF15AP1CC.pdf (6 pages)

Specifications of JF15AP1FF

Circuit

SPST-NO

Switch Function

Off-Mom

Contact Rating @ Voltage

0.05A @ 24VDC

Actuator Type

Square Button

Illumination Type, Color

LED, Green

Mounting Type

Through Hole

Termination Style

PC Pin

Operating Force

3 N

Actuator

Square

Contact Current Rating

50 mAmps at 24 VoltsDC

Ground Terminal

Contact Form

SPST

Mounting Direction

Straight

Body Size

26.9 mm L x 17.7 mm W x 7.3 mm H

Features

Extremely low profile of 5 mm from PCB to top of switch with Green LED, flush actuator, full face illumination

Mounting Style

Through Hole

Operating Temperature Range

- 25 C to + 70 C

Travel

0.4 mm

Contact Rating

50 mAmps at 24 VoltsDC

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Illumination Voltage (nominal)

Lead Free Status / Rohs Status

Lead free / RoHS Compliant

Other names

360-1268
JF15APC1FF

Current page: 1 of 6
Download datasheet (489Kb)

General

Series JF

Electrical Capacity (Resistive Load)

Other Ratings

Materials & Finishes

Environmental Data

PCB Processing

Standards & Certifications

J40

Operating Temperature Range:

Nominal Operating Force:

Insulation Resistance:

Stationary Contacts:

Contact Resistance:

Dielectric Strength:

Movable Contact:

Low/Logic Level:

Mechanical Life:

Electrical Life:

Total Travel:

Soldering:

Terminals:

Vibration:

Humidity:

Cleaning:

Actuator:

Shock:

Case:

Base:

Seal:

Specifications

50mA @ 24V DC

50 milliohms maximum

500 megohms minimum @ 250V DC

250V AC minimum for 1 minute minimum

500,000 operations minimum

3.0N for flush actuator

2.0N for sculptured actuator

Flush Actuators .016” (0.4mm); Sculptured Actuator: .031” (0.8mm)

Polyamide for spot illuminated; polycarbonate for full face

Glass fiber reinforced polyamide

Nitrile butadiene rubber

Glass fiber reinforced polyester

Phosphor bronze with silver plating

Brass with silver plating

–25°C through +70°C (–13°F through +158°F)

90 ~ 95% humidity for 96 hours @ 40°C (104°F)

10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning

in 1 minute; 3 right angled directions for 2 hours

50G (490m/s

Wave Soldering recommended. See Profile A in Supplement section.

Manual Soldering: See Profile A in Supplement section.

Automated cleaning. See Cleaning specifications in Supplement section.

Switches should not be operated or have any pressure on the actuators during cleaning.

Full face illuminated models suitable only for bottom board spray wash to avoid contamination

of the 2-layered actuator, which may compromise the aesthetics.

The JF Series tactiles have not been tested for UL recognition or CSA certification.

These switches are designed for use in a low-voltage, low-current, logic-level circuit.

When used as intended in a logic-level circuit, the results do not produce hazardous energy.

) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)

www.nkk.com

Illuminated Ultra-Thin Process Sealed Tactiles

Related parts for JF15AP1FF

JF15AP1FF Summary of contents

Page 1

... Manual Soldering: See Profile A in Supplement section. Cleaning: Automated cleaning. See Cleaning specifications in Supplement section. Switches should not be operated or have any pressure on the actuators during cleaning. Full face illuminated models suitable only for bottom board spray wash to avoid contamination of the 2-layered actuator, which may compromise the aesthetics. ...

Page 2

... Terminal spacing conforms to standard .100” (2.54mm) PCB grid. Matching indicator available and shown at the end of Section M. Common Bus Matrix These single pole, single throw switches can be used in a key- board matrix and, using strapped terminals, achieve a com- mon bus electrical configuration on a single-sided PC board. ...

Page 3

Series Pole & Circuit 15 SPST OFF (ON Momentary Illumination R Spot Full Face (with A square actuator only) DESCRIPTION FOR TYPICAL ORDERING EXAMPLE J Red LED for Spot Illumination SPST OFF-(ON) Circuit Actuator ...

Page 4

Illuminated Ultra-Thin Process Sealed Tactiles ILLUMINATION & ACTUATOR TYPES R Spot Illumination 1 2 Square Actuator Round Actuator Actuator Colors Available Housing is black C D Color Codes: Red Versatile panel arrangements can be made ...

Page 5

Series JF Spot Illuminated with Square Actuator (2.2) .087 (13.95) .549 (11.43) .450 (8.85) .348 JF15RP1CC Spot Illuminated with Round Actuator (2.2) .087 (13.95) .549 (11.43) .450 (8.85) .348 JF15RP2CC Spot Illuminated with Sculptured Actuator (2.2) .087 (13.95) .549 (11.43) ...

Page 6

... Illuminated Ultra-Thin Process Sealed Tactiles NKK Switches can provide custom legends for caps. Contact factory for more information. (12.48) Sq (0.76) Typ .491 .030 (14.0) Sq .551 Recommended Print Method: Screen Print or Pad Print Epoxy based ink is recommended. LEGENDS Suggested Printable Area (8.03) ...

Related keywords

JF15AP1FF datasheet
JF15AP1FF data sheet
JF15AP1FF pdf datasheet
JF15AP1FF component
JF15AP1FF part
JF15AP1FF distributor
JF15AP1FF RoHS
JF15AP1FF datasheet download