XS3F-M422-405-A Omron, XS3F-M422-405-A Datasheet - Page 26

• Manufacturer Part Number: XS3F-M422-405-A
• Description: CONN CABLE STNDRD L-SHAPED M8 5M
• Manufacturer: Omron
• Series: XS3r

Specifications of XS3F-M422-405-A

• Cable Type: Round
• Connector Type: Circular 04 pos Female, Right Angle to Wire Leads
• Length: 16.40' (5m)
• Color: Gray
• Shielding: Unshielded
• Usage: Industrial Environments - IP67
• Svhc: Bis (2-ethyl(hexyl)phthalate) (DEHP) (15-Dec-2010)
• Cable Assembly Type: Sensor
• Cable Length: 5m
• Connector Type A: M8 90° Plug
• Number Of Positions / Contacts: 4
• Contact Plating: Gold over Nickel
• Contact Material: Phosphor Bronze
• Gender: Female
• Current Rating: 3 A
• Mounting Style: Cable
• Termination Style: Solder
• Housing Material: Polyester Elastomer
• Insulation Resistance: 1000 MOhms
• Mounting Angle: Right
• Operating Temperature Range: - 25 C to + 70 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: XS3FM422405A

(5) Mounting Cap
Note: If the cap is not tighten securely enough, the degree of protection (IP67)
(6) After Assembly
Recommended Cables
When connecting a commercially available cable to a
connector assembly, use a cable with an outside diameter of
3 to 6 mm and core sizes of 0.18 to 0.75 mm
connectors and 0.5 mm
Connector Arrangement
For safety, when constructing a connection system between a
Sensor and panel with a connector, make sure that the
connector plug is on the Sensor side and the connector socket
is on the panel side (i.e., the female pins are located on the
power-supply side).
• Align the triangular marks on the pin block and cover and
• Press them together firmly (0.39 to 0.49 N·m) until the pin
• After mounting the cover to the pin block and the cover
• After fully tightening the cap, length A should be
For 6-mm-dia. cable
For 4-mm-dia. cable
For 3-mm-dia. cable
• Confirm the insulation between cores after completing
insert the pin block into the cover.
block does not come out of the cover.
snaps into place, tighten the cap securely by hand within a
torque of 0.39 and 0.49 N·m.
approximately one of the following according to the cable
external diameter and the Connector model.
assembly.
Sensor Side
(Plug)
Pin Block
(Screw-mounting Connectors)
may not be maintained or vibration may cause the cap to become loose.
Do not tighten the cap with pliers or similar tools; they may damage the
cap.
Connector
Cover lock
(Socket)
Connecting Cable
Triangle mark
Pin block
2
maximum for soldering connectors.
6 mm
Cable external diameter (mm)
---
---
1
Cover
(Plug)
A
5 mm
---
0
2
Cap
Panel Side
(Power-supply Side)
4 mm
2
---
1
2
for crimping
(Socket)
3 mm
---
---
1
Safety Precautions
Do not use the product in atmospheres or environments that
exceed product ratings.
Tightening Cap (Connector Assemblies)
1. Do not use pliers to tighten caps, otherwise the caps may
2. If caps are not tightened securely, the Connectors may not
Connector Connection and Disconnection
Degree of Protection
Setup
• When connecting or disconnecting Connectors, be sure to
• Do not hold the cable part when disconnecting Connectors.
• Connectors mating with sockets must be fully inserted into
• Fully tighten thread bracket within a torque range between
• When disconnecting Connectors, be sure to loosen the
• Thread brackets must be loosened in the cutout direction.
• Do not impose external force continuously on the joints of
• The degree of protection of connectors (IP67) is not for a
• Connectors are of resin mold construction. Do not impose
• Do not make any cable bends near the base of the Unit.
• Any bends made must have a minimum radius of 40 mm.
hold the Connectors by hand.
the sockets. Tighten the thread bracket carefully so that the
threads will not be damaged.
0.39 and 0.49 N·m and be sure that the threads of the
opposite parts are hidden by the thread bracket.
thread brackets first. Do not loosen the caps.
pin blocks and covers, otherwise the Connectors may not
keep its proper degree of protection (i.e., IP67).
fully watertight structure. Do not use them underwater.
excessive force on them.
be damaged. Be sure to tighten each cap by hand within a
torque range between 0.39 and 0.49 N·m.
maintain their proper degree of protection (i.e., IP67) or the
caps may become loose due to vibration.
Precautions for Correct Use
Loosen
Thread
bracket
Cutout
XS2
26