AB11AP-FA NKK Switches, AB11AP-FA Datasheet - Page 2

SW PB SPST STRAIGHT BK CAP PCB

AB11AP-FA

Manufacturer Part Number
AB11AP-FA
Description
SW PB SPST STRAIGHT BK CAP PCB
Manufacturer
NKK Switches
Series
ABr
Type
Standardr
Datasheets

Specifications of AB11AP-FA

Circuit
SPST-NO
Switch Function
Off-Mom
Contact Rating @ Voltage
0.4VA @ 28VAC/DC
Actuator Type
Round Button
Mounting Type
Through Hole
Termination Style
PC Pin
Contact Form
SPST
Contact Rating
0.4 Volt-Amp
Actuator
Button, Round
Supply Voltage
28 Volts
Mounting Style
Panel
Terminal Seal
Epoxy
Contact Plating
Gold
Illumination
Not Illuminated
Dielectric Strength
500 Volts
Features
Subminiature size saves space on PC board
Housing Material
Polyamide, Glass Fiber Reinforced
Insulation Resistance
500 MOhms
Led Supply Voltage
28 Volts
Operating Force
2.55 N
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Illumination Type, Color
-
Illumination Voltage (nominal)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
General Specifications
NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
Electrical Capacity (Resistive Load)
Other Ratings
Materials & Finishes
Environmental Data
Installation
PCB Processing
Standards & Certifications
Nominal Operating Force:
Operating Temp Range:
Cap Installation Force:
Insulation Resistance:
Stationary Contacts:
or CSA Certification:
Contact Resistance:
Dielectric Strength:
Movable Contact:
Support Bracket:
Mechanical Life:
Contact Timing:
UL Recognition
Case Housing:
Electrical Life:
Logic Level:
Soldering:
Terminals:
Vibration:
Humidity:
Cleaning:
Plunger:
Travel:
Shock:
Manual Soldering: See Profile B in Supplement section.
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
50,000 operations minimum
50,000 operations minimum
2.55N
Nonshorting (break-before-make)
Pretravel .028” (0.7mm); Overtravel .016” (0.4mm); Total Travel .043” (1.1mm)
Polyacetal
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Brass with gold plating
Brass with gold plating
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
49.03N (11.2 lbf) maximum downward force on actuator
Wave Soldering Recommended: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
The AB Series pushbuttons have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
Process Sealed Subminiature Pushbuttons
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Series AB
03-07

Related parts for AB11AP-FA