D2F-01F Omron, D2F-01F Datasheet - Page 6
![BUTTON SWITCH PCB SPDT .1A 75GF](/photos/15/24/152426/d2f-f__d2f__d2f-01__d2f-01f_sml.jpg)
D2F-01F
Manufacturer Part Number
D2F-01F
Description
BUTTON SWITCH PCB SPDT .1A 75GF
Manufacturer
Omron
Series
D2Fr
Type
Snap Actionr
Specifications of D2F-01F
Circuit
SPDT
Switch Function
On-Mom
Contact Rating @ Voltage
0.1A @ 30VDC
Actuator Type
Round (Pin Plunger)
Mounting Type
Through Hole
Termination Style
PC Pin
Operating Force
75gf
Contact Form
SPDT
Contact Rating
0.1 Amp
Actuator
Plunger, Pin
Microswitch Type
Ultra Subminiature
Actuator Style
Pin Plunger
Operating Force Max
75gf
Contact Voltage Ac Nom
125V
Contact Voltage Dc Nom
30V
Contact Current Max
100mA
Body Style
Ultra Subminiature
Brand/series
D2F-01 Series
Current, Rating
0.1 A
Dielectric Strength
1500 VAC
Force, Operating
75 g
Mounting Hole Size
1.2 mm
Number Of Poles
1
Operation
Snap Action
Standards
UL Listed, CSA Certified, RoHS Compliant
Temperature Rating
-25 to +65 °C
Termination
Through Hole
Voltage, Rating
30 VDC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
D2F01F
SW502
SW502
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
D2F-01F
Manufacturer:
OMRON
Quantity:
365
Company:
Part Number:
D2F-01FL3
Manufacturer:
OMRON
Quantity:
5 000
Precautions
Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide,
“Snap Action Switches, Technical Information” for correct use.
■ Correct Use
Mounting
Turn OFF the power supply before mounting or removing the switch,
wiring the switch, or performing maintenance or inspection. Failure to
do so may result in electric shock or burning.
Mount the switch onto a flat surface. Mounting on an uneven surface
may cause deformation of the switch, resulting in faulty operation or
breakage of the housing.
Allow sufficient insulation distance between terminals, terminal
traces and between terminals and ground.
Operating Stroke Setting
Take particular care in setting the operating stroke for the pin plunger
models. Make sure that the operating stroke is 70% to 100% of the
rated OT distance. Do not operate the actuator exceeding the OT
distance, otherwise the service life of the switch maybe decreased.
Using Microloads
Using a model for ordinary loads to switch microloads may result in
faulty operation. Instead, use the models that are designed for micro-
loads and that operate in the following range;
However, even when using microload models within the operating
range shown above, if inrush current or inductive voltage spikes
occur when the contact is opened or closed, it may increase contact
wear and so decrease the service life. Therefore, insert a contact
protection circuit where necessary.
36
Snap Action Switch
Inoperable
range
Operating range
for micro load
models D2F-01
D2F
Current (mA)
Operating
range for
general-load
models
D2F
■ Cautions
Terminal Connection
When soldering a lead wire to the terminal, first insert the lead wire
conductor into the terminal hole and then perform soldering.
Make sure that the capacity of the soldering iron is 30 W maximum
and that the temperature of the soldering tip is approximately 300 °C.
(350 °C maximum.) Complete soldering within 3 s. After soldering,
do not apply external force to the soldered area for about 1 minute.
Using a switch with improper soldering may result in abnormal heat-
ing, possibly resulting in a burn.
Applying the soldering iron for more than 3 s or using an iron that is
rated for more than 30 W may deteriorate the switch characteristics.
When soldering the lead wire to the PCB terminal, pay careful
attention so that the flux and solder liquid level does not exceed the
PCB level.