D2SW-3L2HS Omron, D2SW-3L2HS Datasheet
D2SW-3L2HS
Specifications of D2SW-3L2HS
D2SW3L2HS
SW237
Related parts for D2SW-3L2HS
D2SW-3L2HS Summary of contents
Page 1
... D2SW- 0.1A @ 125VAC/0.1A 01TS @ 30VDC D2SW- 0.1A @ 01L1DS 125VAC/0.1A @ 30VDC 0.1A @ D2SW- 01L1HS 125VAC/0.1A @ 30VDC 0.1A @ D2SW- 01L1MS 125VAC/0.1A @ 30VDC 0.1A @ D2SW- 125VAC/0.1A 01L1TS @ 30VDC D2SW- 0.1A @ 125VAC/0.1A 01L2DS @ 30VDC D2SW- 0.1A @ 125VAC/0.1A 01L2HS Contact Operating Seal ...
Page 2
... D2SW Pin 125VAC/3A plunger 3MS @ 30VDC D2SW Pin 3TS 125VAC/3A plunger @ 30VDC 3A @ Hinge D2SW- 3L1DS 125VAC/3A lever @ 30VDC 3A @ Hinge D2SW- 3L1HS 125VAC/3A lever @ 30VDC D2SW Hinge 3L1MS 125VAC/3A lever @ 30VDC D2SW Hinge 125VAC/3A lever 3L1TS @ 30VDC D2SW Hinge 125VAC/3A roller ...
Page 3
... Hinge 3L2TS 125VAC/3A roller @ 30VDC lever 3A @ Simulated D2SW- 3L3DS 125VAC/3A roller @ 30VDC lever 3A @ Simulated D2SW- 3L3HS 125VAC/3A roller @ 30VDC lever D2SW Simulated 3L3MS 125VAC/3A roller @ 30VDC lever D2SW Simulated 125VAC/3A roller 3L3TS @ 30VDC lever SPDT 60g IP67 Lead Wires - Bottom SPDT ...
Page 4
... Model Model 3 A Model 0.1 A D2SW-3HS D2SW-01HS D2SW-3TS D2SW-01TS D2SW-3DS D2SW-01DS D2SW-3MS D2SW-01MS D2SW-3L1HS D2SW-01L1HS D2SW-3L1TS D2SW-01L1TS D2SW-3L1DS D2SW-01L1DS D2SW-3L1MS D2SW-01L1MS D2SW-3L3HS D2SW-01L3HS D2SW-3L3TS D2SW-01L3TS D2SW-3L3DS D2SW-01L3DS D2SW-3L3MS D2SW-01L3MS D2SW-3L2HS D2SW-01L2HS D2SW-3L2TS D2SW-01L2TS D2SW-3L2DS D2SW-01L2DS D2SW-3L2MS D2SW-01L2MS Snap Action Switch D2SW 1 ...
Page 5
... D2SW-01 600 VAC, 50/60 Hz for 1 min. between con- tacts of the same polarity — — 200,000 operations min. Lead wire model D2SW-3L2@S D2SW-3MS D2SW-01L2@S D2SW-01MS 60 g 180 — 0.6 mm 1.0 mm 0.5 mm 0.8 mm 0.1 mm 19.3 mm — ...
Page 6
... Non-inductive load Lamp load — — — — SPST- Consult Omron for ordering information Inductive load Inductive load Motor load 0 0.5 A 0.3 A 0 Inductive load Inductive load Motor load — — SPST-NO ( Consult Omron for ordering information D2SW Snap Action Switch ...
Page 7
... Simulated Roller Lever D2SW-3L3@S D2SW-01L3@S ■ Hinge Roller Lever D2SW-3L2@S D2SW-01L2@S Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions. 2. The above illustrations and dimensions are for models with solder terminals. Refer to “Terminals” for models with tab (#110) and PCB terminals ...
Page 8
... The above illustrations and dimensions are for models with pin plungers. The dimensions and operating characteristics of the actuators of models incorporating them are the same as those of the actuators of models with both actuators and terminals. ■ Terminals Solder Terminals PCB Terminals Note: Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions. Tab Terminals (#110) PCB Mounting D2SW Snap Action Switch 5 ...
Page 9
... Tighten the screws to a torque of 0.23 to 0.26 N • m (2.3 to 2.7 kgf • cm) Mounting holes When soldering a lead wire to a terminal of the D2SW, use a solder- ing iron with a maximum capacity and do not take more than 5 seconds to solder the lead wire, otherwise the characteristics of the D2SW may be altered ...