SS-01GL Omron, SS-01GL Datasheet

Page 1

... SS-01D1 0.1A @ 125VAC/0.1A plunger @ 30VDC 0.1A @ SS-01D2 125VAC/0.1A plunger @ 30VDC SS-01T 0.1A @ 125VAC/0.1A plunger @ 30VDC SS-01-E 0.1A @ 125VAC/0.1A plunger @ 30VDC 0.1A @ SS-01- ED 125VAC/0.1A plunger @ 30VDC 0.1A @ SS-01- ET 125VAC/0.1A plunger @ 30VDC SS-01-F 0.1A @ 125VAC/0.1A plunger @ 30VDC SS-01- 0.1A @ 125VAC/0.1A plunger FD @ 30VDC ...

Page 2

... SS- 0.1A @ Hinge 125VAC/0.1A lever 01GL-F @ 30VDC Part Rated Actuator Resistive types Load - Switch 0.1A @ Hinge SS- 01GL-FD 125VAC/0.1A lever @ 30VDC 0.1A @ Hinge SS- 125VAC/0.1A lever 01GL-FT @ 30VDC SS- 0.1A @ Simulated 125VAC/0.1A roller 01GL13 @ 30VDC lever SS- 0.1A @ Simulated 125VAC/0.1A roller 01GL13D @ 30VDC lever SS- 0.1A @ ...

Page 3

... SS-01GL2D — — Soldered Tab (#110) terminal terminal SS-01-E SS-01-ET SS-01-F SS-01-FT SS-01 SS-01T SS-01GL-E SS-01GL-ET SS-01GL-F SS-01GL-FT SS-01GL SS-01GLT SS-01GL13-E SS-01GL13-ET SS-01GL13-F SS-01GL13-FT SS-01GL13 SS-01GL13T SS-01GL14-E SS-01GL14-ET SS-01GL14-F — SS-01GL14 SS-01GL14T SS-01GL2-E SS-01GL2-ET SS-01GL2-F SS-01GL2-FT SS-01GL2 SS-01GL2T SS Snap Action Switch 1 ...

Page 4

... Humidity Service life Mechanical Electrical Weight Note: 1. SS-10 series only. 2. 50,000 operations minimum for the SS-10 series. 3. Applies to the pin plunger type (at the pin plunger of the lever type million operations for the SS-10 series. 5. Data shown are of initial value Snap Action Switch ...

Page 5

... NO 0 max. SS-10 SS-01GL-E 150 0.6 mm (0.024 in) 1.2 mm (0.047 in) 0.4 mm (0.016 in) 0.8 mm (0.032 in) 0.12 mm (0.005 in) 13.6 mm (0.535 in) 8.4 ± 0.5 mm 8.8 ± 0.8 mm (0.331 ± ...

Page 6

... SS-10 series must have a power factor of 0.75 min. 3. Lamp load has an inrush current of 10 times the steady-state current 4. Motor load has an inrush current of 6 times the steady-state current the switch is used circuit and is subjected to inrush current or surge, connect a surge suppressor across the switch. ■ Contact Resistance Contact rating: ...

Page 7

... Engineering Data ■ Mechanical service life Standard type (SS-5, SS-10 series) Dimensions Unit: mm (inch) ■ Pin Plunger SS-01 (-E, -F) SS-5 (-F) SS-10 ■ Hinge Lever SS-01GL (-E, -F) SS-5GL (-F) SS-10GL ■ Electrical service life Standard type (SS-5 series) Snap Action Switch SS 5 ...

Page 8

... Straight vertical PCB terminal models are shown above. Soldered terminal, Tab (#110) terminal, lead wire terminal, PCB terminal parallel to left and PCB terminal parallel to right are shown in the Terminals section. ■ Hinge Roller Lever SS-01GL2 (-E, -F) SS-5GL2 (-F) SS-10GL2 Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. ...

Page 9

... Unit: mm (inch) ■ Terminals General-Purpose Type PCB terminal, straight vertical (D) PCB terminal, parallel to left (D1) Note: Thickness of all the terminals is 0.5 mm. Soldered terminal (blank) PCB terminal, parallel to right (D2) Quick-connect tab (#110) terminal (T) Snap Action Switch SS 7 ...