D2VW-5-1HS Omron, D2VW-5-1HS Datasheet - Page 2
![SWITCH BASIC SPDT 5A .187QC](/photos/15/28/152897/d2vw-5-1hs_sml.jpg)
D2VW-5-1HS
Manufacturer Part Number
D2VW-5-1HS
Description
SWITCH BASIC SPDT 5A .187QC
Manufacturer
Omron
Series
D2VWr
Type
Snap Actionr
Specifications of D2VW-5-1HS
Circuit
SPDT
Switch Function
On-Mom
Contact Rating @ Voltage
5A @ 125VAC
Actuator Type
Round (Pin Plunger)
Mounting Type
Chassis Mount
Termination Style
Solder, Quick Connect - .187" (4.7mm)
Operating Force
200gf
Contact Form
SPDT
Contact Rating
3 Amps at 125 Volts, 250 Volts
Actuator
Plunger, Pin
Microswitch Type
Miniature
Actuator Style
Pin Plunger
Operating Force Max
200gf
Contact Voltage Ac Nom
250V
Contact Voltage Dc Nom
125V
Contact Current Max
5A
Body Style
Miniature
Current, Rating
5 A
Dielectric Strength
1500 VAC
Ip Rating
IP50
Mounting Hole Size
3.1 mm
Number Of Poles
1
Operation
Snap Action
Termination
Solder/Quick Connect
Voltage, Rating
250/30 VAC/VDC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
D2VW51HS
SW433
SW433
Specifications
■ Characteristics
Note: 1. Data shown are of initial value.
■ Ratings
D2VW-5
D2VW-01
Note: 1. The resistive load ratings apply under the following test conditions:
208
Operating speed
Operating frequency
Insulation resistance
Contact resistance
Dielectric strength (See note 2)
Vibration resistance (See note 3)
Shock resistance (See note 3)
Degree of protection
Degree of protection against electric shock
Proof tracking index (PTI)
Ambient operating temperature
Ambient operating humidity
Life expectancy
Weight
Rated Voltage
125 VAC
250 VAC
30 VDC
125 VDC
Rated Voltage
125 VAC
30 VDC
2. The dielectric strength shown is measured using a separator between the switch and metal mounting plate.
3. For the pin plunger models, the above values apply for use at the free position and total travel position. For the lever models, the values
4. The operating temperature of the lead wire (AV0.75f) for non-UL/CSA molded lead wire models is between -40 to 85°C.
2. The above current ratings are the values of the steady-state current.
3. Inductive load has a power factor of 0.7 min. (AC) and a time constant of 7 ms max. (DC).
4. Lamp load has an inrush current of 10 times the steady-state current.
5. Rating for UL/CSA approval is as follows (See “Approved Standards” section):
apply at the total travel position.
Ambient Temperature = 20±2°C, Ambient Humidity = 65±5%, Operating frequency = 30 operations/min.
Sealed Snap Action Switch
D2VW-01
D2VW-5
(reference values)
5 A
5 A
5 A
0.4 A
0.1 A
0.1 A
NC
NC
Resistive load
Resistive load
0.1A @ 125 VAC
0.1A @ 30 VDC
3A @ 125 VAC, 250 VAC
Mechanical
Electrical
Non-inductive load
Non-inductive load
Model
NO
NO
0.1 mm to 1 m/s (at pin plunger)
Mechanical: 300 operations/minute max.
Electrical: 30 operations/minute max.
100 MΩ min. (at 500 VDC)
50 mΩ max. (100 mΩ max. for molded lead wire models)
1,000 VAC, 50/60 Hz for 1 min. between terminals of the same polarity
1,500 VAC, 50/60 Hz for 1 min. between each current-carrying metal parts and ground, and
between each terminal and non-current-carrying metal parts.
Malfunction: 10 to 55 Hz, 1.5 mm double amplitude
Destruction: 1,000 m/s
Malfunction: 300 m/s
IEC IP67 (excluding the terminals on terminal models).
Class I
175
95% max. (for 5°C to 35°C)
10,000,000 operations min. at 60 operations per minute
1,000,000 operations min. at 30 ops. per minute. 100,000 operations min. at 30 ops. per minute
Approx. 7g (pin plunger models without wires)
-40° to 85°C (at 60% RH max.) with no icing
D2VW
0.5 A
0.5 A
3 A
0.1 A
—
—
NC
NC
Lamp load
Lamp load
D2VW-01
2
(approx. 30G) max.
2
NO
NO
(approx. 100G) max.
4 A
4 A
4 A
0.4 A
—
—
NC
NC
Inductive load
Inductive load
NO
NO
Inductive load
Inductive load
—
—
—
—
—
—
D2VW-5
NC
NC
Motor load
Motor load
NO
NO